Yamaha DTX-Multi12 Multi-Pad Electronic Percussion Instrument - Manual (Page 41)

TRIGGER
Ref
erence
KIT
MIDI
V
OICE
UTILITY
W
A
VE
PA
TTERN
Internal Design
Owner’s Manual 41
*3 The Top parameter’s setting is valid only when equal to or greater
than that of the Bottom parameter.
LFOSpeed
[TempoFlanger, G Chorus, 2 Modulator, SPX Chorus,
Symphonic, and Tremolo]
This parameter is used to set the modulation frequency.
[TempoPhaser]
This parameter is used to set the modulation speed in
terms of note lengths.
[AutoPan]
This parameter is used to set the auto-pan frequency.
LFOWave
[AutoWah]
This parameter is used to specify whether the filter-
sweep effect is produced using a sine or square wave.
[AutoPan]
This parameter is used to set the panning curve.
Livenss
This parameter is used to set the way in which early
reflections decay.
LowAtk
This parameter is used to set the amount of time that
elapses before compression is fully applied in the low-
frequency band.
LowGain
This parameter is used to set the output level of the low-
frequency band.
LowLvl This parameter is used to set the low-frequency level.
LowMute
This parameter is used to activate and deactivate low-
frequency muting.
LowRat
[MltBndComp]
This parameter is used to set the compression ratio for
the low-frequency band.
[Reverb effects]
This parameter is used to adjust the low-frequency com-
ponent.
LowTh
This parameter is used to set the input-signal level at
which the compressor starts to process the sound in the
low-frequency band.
LPF
This parameter is used to set the low-pass filter’s cutoff
frequency.
M.Freq
This parameter is used to set the center frequency of the
mid-frequency EQ band.
M.Gain
This parameter is used to set the amount by which the
mid-frequency EQ band is boosted or cut.
M.Width
This parameter is used to set the width of the mid-fre-
quency EQ band.
Manual
This parameter is used to set the phase-modulation off-
set value.
MicAngl
This parameter is used to set the left-right inclination of
the microphone used to capture the speaker’s output.
MidAtk
This parameter is used to set the amount of time that
elapses before compression is fully applied in the mid-
frequency band.
MidGain
This parameter is used to set the output level of the mid-
frequency band.
MidLvl This parameter is used to set the mid-frequency level.
MidMute
This parameter is used to activate and deactivate mid-
frequency muting.
MidRat
This parameter is used to set the compression ratio for
the mid-frequency band.
MidTh
This parameter is used to set the input-signal level at
which the compressor starts to process the sound in the
mid-frequency band.
MixLvl
This parameter is used to set how much of the effect
sound is mixed back into the dry sound.
Mode
This parameter is used to adjust the mode of operation
of the phaser.
MoveSpeed
This parameter is used to specify the amount of time that
elapses until the sound set using the Vowel parameter is
produced.
On/Off
This parameter is used to activate and deactivate the
isolator.
OutLvl This parameter is used to set the output level.
OutLvl1 This parameter is used to set the first-stage output level.
OutLvl2
This parameter is used to set the second-stage output
level.
Output This parameter is used to set the output level.
Parameter
name
Descriptions
OverDr
This parameter is used to adjust the way in which the
sound distorts.
Pan1
This parameter is used to set the first stereo-panning
position.
Pan2
This parameter is used to set the second stereo-panning
position.
PanDirectn This parameter is used to set the auto-pan type.
PhShiftOfst
This parameter is used to set the phase-modulation off-
set value.
Pitch1
This parameter is used to set the first pitch in semi-tone
units.
Pitch2
This parameter is used to set the second pitch in semi-
tone units.
PMDepth
This parameter is used to set the depth of pitch modula-
tion.
Presenc
Often seen on guitar amplifiers and the like, this parame-
ter is used to control the high-frequency band.
Ratio This parameter is used to set the compression ratio.
Release
This parameter is used to set the amount of time that
elapses until the sound is no longer being compressed.
Resonance This parameter is used to set the resonance of the filter.
ResoOfst This parameter is used to set the resonance offset value.
RevDly
This parameter is used to set the interval between early
reflections and subsequent reverberation.
RevTime This parameter is used to set the reverb time.
RoomSize This parameter is used to set the size of the room.
Rotor/Horn
This parameter is used to set the relative volumes of the
high-frequency horn and the low-frequency rotor.
RotorF
This parameter is used to set the speed of rotation of the
low-frequency rotor at the “fast” setting.
RotorS
This parameter is used to set the speed of rotation of the
low-frequency rotor at the “slow” setting.
Sens
This parameter is used to set how sensitive the wah filter
is to changes in the input level.
S-FTmHorn
This parameter is used to set how long it takes for the
high-frequency horn to switch between fast and slow
rotation speeds.
S-FTmRotor
This parameter is used to set how long it takes for the
low-frequency rotor to switch between fast and slow
rotation speeds.
Speaker
This parameter is used to select the type of speaker to
be simulated.
Speed
[PhaserMono and PhaserStereo]
This parameter is used to set the frequency of the LFO
that controls cyclic changes in phase modulation.
[AutoWah]
This parameter is used to set the LFO speed.
SpeedCtrl
This parameter is used to set the rotation speed as “fast”
or “slow”.
Spread
This parameter is used to set how wide the effect’s out-
put sounds.
Stage
This parameter is used to set the number of phase-filter
steps.
Thresh
This parameter is used to set the input-signal level at
which the effect starts to process the sound.
Top *3
This parameter is used to set the highest point in the fil-
ter’s sweep range.
Type
[Wah effects]
This parameter is used to set the wah-effect type.
[EarlyRef, GateReverb, and ReverseGate]
This parameter is used to set the reflected-sound type.
Vowel This parameter is used to select a vowel type.
Parameter
name
Descriptions