haier Silver Sea-ox FCD-JTHMG50-III - Manual (Page 2)

Pre-safe Expert
Contents
Installation
2 Special reminding
2-3 Features
3 Views and parts
4 Safety precautions
5
5
6
6 Attentions in Installation
7 Installation
Operation
8
8
Control panel illustration
Operation diagram
14
8-12
14
12
13
13
14
Packing list
Operation instructions
Attentions in operation
Electric Circuit Diagram
Electric Circuit Diagram
FAQ*After service
Cleaning and maintenance
FAQ
Before USage
See to the physical product for the appearance,color or pattern.
Remote controller panel illustration
Use of remote controller
Mark of HAIER-THERMOCOOL
Safe Water Heaters
This mark is the designation for Pre-Safe Expert of
HAIER-THERMOCOOL Water Heater Company, which
indicates use of the company's patented technology
inside the product. It ensures you a safe bath while
monitoring whether your house ground wire is live or
not all the time. If this mark is lighted on, it indicates
your house ground wire has come live (poor
grounding and live). In this case, please immediately
stop use and unplug from the power supply, and
remember not to touch any electric appliance shell in
your house. At the same time, immediately contact
after-sales service and your property management
company for professional repair until the mark goes
off.
Pre-Safe Expert will become the electric safeguard
for your family.
Setting environment
Parameters
Dimensions
Problems
No outlet water
Outlet water is cold
Outlet water flow and
temperature is not steady
Unable to start machine
Error display of E1
Error display of E2
Error display of E3
Possible Causes to be Confirmed
If water supply is stopped or water
pressure is too low
If use point is blocked or if hot water
valve is open
If water temperature is properly adjusted
If thermostat is out of control
Heating time is too short
If city water pressure is steady
If components are damaged
Circuit fault
If tank is full of water or if components
are damaged
If sensor is damaged
Corrective Measures
Check
Check and clean
Re-adjust
Contact service station
Continue heating
Check
Contact service station
Contact service station
Contact service station
Fill water full or contact
service station
External Cleaning: Disconnect power supply before cleaning. Gently wipe with wet
cloth dipped with a little of mild detergent. Do not use gasoline or other solvents. Finally
dry with dry cloth. Keep water heater dry. Do not use cleansers containing grinding
agent (e.g. toothpaste), acids, chemical solvents (e.g. alcohol) or polishers to clean.
Internal Cleaning: To ensure high working efficiency, heating elements and tank liner of
water heater shall be cleaned once in three years. Take care not to damage protection
layer on heating elements and tank liner inner surface. According to different local
water qualities and use habits, magnesium anode rod shall be periodically replaced. If
maintenance is needed, please contact local service station.
Cleaning and Maintenance
This water heater shall only be repaired and maintained by qualified
servicemen. Improper maintenance may cause severe injury or damage.
Before opening or repairing water heater, please do pull out the power plug. Statement:
Note: Before asking for service, please refer to troubleshooting section to resolve easy
problems.
FAQ
Packing List
2 1 2 1 1 1 1 2
Water Heater
(set) Safety Valve
(pcs)
Expansion
bolt
(pcs) Expansion
hook
(pcs)
Name
Quantity
User manual
(copy)
Battery
(pcs)
Remote
controller
(pcs)
Drain hose
(ply)
Correct Disposal of this product:
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.