FRIGIDAIRE 318205804 - Manual (Page 31)

31
SETTING OVEN CONTROLS
SETTING THE SABBATH FEATURE (for use on
the Jewish Sabbath & Holidays)
The BAKE TIME and DELAY START pads are used to
set the Sabbath feature. The Sabbath feature may only be
used with the BAKE pad. The oven temperature may be
set higher or lower after setting the Sabbath feature (the
oven temperature adjustment feature should be used only
during Jewish Holidays), however the display will not visibly
show or provide any audible tones indicating whether the
change occurred correctly. Once the oven is properly set
using Bake with the Sabbath feature active, the oven will
remain continuously ON until cancelled. This will override
the factory preset 6-Hour Energy Saving feature.
If the oven light will be needed during the Sabbath, press
OVEN LIGHT before activating the Sabbath feature.
Once the oven light is turned ON and the Sabbath feature
is active, the oven light will remain ON until the Sabbath
feature is turned OFF. If the oven light needs to be OFF,
be sure to turn the oven light OFF before activating the
Sabbath feature.
IMPORTANT
It is not advised to attempt to activate any other program
feature other than BAKE while the Sabbath feature is
active. ONLY the following key pads will function after
setting the Sabbath feature; 0 to 9, BAKE, START &
CANCEL. All other keypads should not be used once
the Sabbath feature is properly activated.
 NOTE
You may change the oven temperature once baking has
started by pressing BAKE, the numeric key pads for the
temperature you want (example for 425°C press 4 2 5)
and then pressing START twice (for Jewish Holidays only).
Remember that the oven control will no longer beep
or display any further changes once the oven is set for
the Sabbath feature.
To Program the Oven to Begin Baking Immediately &
activate the Sabbath feature (example: baking at 350°F)
1. Be sure that the clock is set with the correct time of day.
2. Place the food in the oven.
3. Press BAKE. “350°” appears in the display.
4. Press START. The actual oven temperature appears in
the display.
5. If you desire to set the oven control for a Bake Time
or Delayed Bake Time do so at this time. If not, skip
this step and continue to step 7. Refer to the Bake
Time / Delay Start section for complete instructions.
Remember the oven will shut down after using Bake
Time or Delay Start and therefore may only be used
once during the Sabbath/Jewish Holidays.
6. The oven will turn ON and begin heating.
7. Press and hold both the BAKE TIME and DELAY
START pads for at least 3 seconds. “SAb” will appear
in the display. Once “SAb” appears in the display the
oven control will no longer beep or display any further
changes and the oven is properly set for the Sabbath
feature.
8. The oven may be turned OFF at any time by fi rst pressing
CANCEL pad (this will turn the oven OFF only). To turn
OFF the Sabbath feature press and hold both the BAKE
TIME and DELAY START pads for at least 3 seconds.
“SAb” will disappear from the display.
Should you experience a power failure or interruption, the
oven will shut off. When power is returned, “SF” (Sabbath
Failure) will be shown in the oven display and on the element
displays which were activated before power failure (models
B & C only). The oven and cooktop will not turn back on
automatically. If your food was nearly fully cooked, you may
allow the trapped heat in the oven to fi nish the cooking
process. Otherwise, you should remove the food when the
power failure occurs, because you may only start the oven
once during the Sabbath/Jewish Holidays. After the Sabbath
observance, turn OFF the Sabbath feature and be sure that
all the control knobs are at the OFF position. The appliance
may be used again with all normal functions.
After the Sabbath observance turn OFF the Sabbath feature.
Press and hold both the BAKE TIME and DELAY pads for at
least 3 seconds. “SAb” will disappear from the display and
the oven may be used with all normal functions. For further
assistance, guidelines for proper usage, and a complete list
of models with the Sabbath feature, please visit the web at
http:\\www.star-k.org.
How the Electronic Surface Element Controls work
when the Sabbath feature is ON (Models B & C only).
When your Oven Sabbath feature is ON, the Electronic
Surface Elements are also in Sabbath mode. This means
that all electronic surface element control displays show
“Sb”. The surface elements can be used even if the Sabbath
Feature is on.
To turn ON a Surface Element when the Oven Sabbath
Feature is active:
If you turn on a surface element when the oven Sabbath
feature is on, the electronic surface element control will record
that request and execute it with a 15-30 seconds delay. So
the element will start heating 15-30 seconds after the surface
element control was turned on. As the oven control, the
surface element display will not show the setting because
“Sb” is on in the displays. When necessary, it is possible to
adjust the power of the surface element but you have to
remember that the surface element control will adjust the
temperature with the same delay.
To turn OFF the Surface Element when the Oven
Sabbath Mode is active:
To shut off the surface element while the Sabbath feature
is ON, proceed as usual but take note that the element will
immediately turn off without any delay.