Garmin 5008 - Manual (Page 60)

5 GPSMAP ® 4000/5000 Series Owner’s Manual
Appendix
Appendix
MARPA: target Lost—(radar) unable to track a MARPA
target any longer.
NMEA Depth Is Below transducer—(sonar) the NMEA
depth input is using the DBT sentence which does not
include keel offset.
No DGPS Position—the unit lost differential GPS
reception (WAAS). Make sure you have a clear view of
the sky.
No Proximity Waypoints Found—no proximity
waypoints found while attempting a user data transfer.
No Routes Found—no routes found while attempting a
user data transfer.
No tracks Found—no tracks found while attempting a
user data transfer.
No User Waypoints Found—no user waypoints found
while attempting a user data transfer.
Not All Maps Fit, Some Maps Will Not Be Drawn—
there are more maps present on the SD card than the unit
can support. Some maps on the card will not be drawn or
used to find map features.
Off Course Alarm—the boat has left the user-defined
course.
Proximity Alarm—the boat has come close to a user-
defined proximity point.
Proximity Alarm Memory is Full—the proximity
waypoint memory is full. Erase existing proximity
waypoints to make room.
Proximity Overlaps Another Proximity Waypoint—a
proximity point is overlapping another proximity waypoint.
Radar Guard Zone Alarm—(radar) an object has been
detected in the user-defined radar guard zone.
Radar Needs Repair Error Code—(radar) the radar needs
repair. An error code will be listed to help diagnose the
error.
Radar Service Incompatible. Software Update
Required—a radar software update is needed. Contact
Garmin Product Support for assistance updating your
network.
Radar Service Lost—(radar) the unit has lost
communications with the remote radar unit. Check the
network and the radar wiring.
Route Already Exists—the named route already exists.
Select another name.
Route is Full—the individual route is full, no more
waypoints can be added.
Route Memory is Full, Can’t Create Route—the
chartplotter route memory is full, no more routes can be
created. Erase existing routes to make room.
Route truncated—some points on the end of the route
have been discarded.
Shallow Water Alarm—(sonar) the boat has entered the
user-defined shallow-water depth.
Simulating Operation—the unit is in Simulator Mode.
Sonar Failed, Unit Needs Repair—there has been a sonar
failure and the unit needs to be sent in for repair. Contact
Garmin Product Support.
Sonar Service Incompatible. Software Update
Required—a software update is needed. Contact Garmin
Product Support for assistance updating your network.
Sonar Service Lost—(sonar) the unit has lost
communications with the remote sonar unit. Check the
network and the sonar wiring.
tide Alarm—the tide has reached the user-specified tide
alarm range.
track Already Exists—the named track already exists.
Select another name.
track Log Full—there is no longer any space in the active
track log storage.
track truncated—some points on the end of the track
have been discarded.
transducer Disconnected, Sonar turned Off—the
transducer has been disconnected. Sonar has been turned
off. Check transducer wiring.
transfer Complete—user data transfer is complete.
Unknown bridge height within calculated auto-guidance
route—(BlueChart g2 Vision) there is an unknown bridge
height within the auto-guidance route.
User Card Not Found—user data card transfer. Make sure
an SD card is fully inserted.
Water Speed Sensor not Working—the water speed
sensor is not working properly. Check the wheel for
obstructions and check wiring.
Water temperature Alarm—(temperature sensor/
transducer) the water temperature has entered or left the
user-defined water temperature alarm zone.
Warning: Auto-guidance route starting position moved
due to safe depth settings—(BlueChart g2 Vision) auto-
guidance has calculated the route, but the starting point has
been moved to deeper water.
Warning: Auto-guidance route ending position moved
due to safe depth settings—(BlueChart g2 Vision) auto-
guidance has calculated the route, but the end point has
been moved to deeper water.
Waypoint Already Exists—the named waypoint already
exists. Select another name.
Waypoint Memory is Full, Can’t Create Waypoint—the
User Waypoint memory is full. Erase existing waypoints to
make room.