GE 47019 - Manual (Page 2)

ge.com
27" built-in single ovens
(continued)
Undercounter installation dimensions (in inches)
Models PK916, JKP70, JKP30 and JKS10
25
Gas or electric cooktops may be installed over this
oven. See cooktop installation instructions for cutout size.
See label on top of oven for approved cooktop models.
Gas or electric connections
for gas cooktop must be
located in an adjacent
accessible location to the right
5
240V / 208V
Junction Box
Location
36"
Typical
Countertop
Height
24
Allow 1"
unit overlap
all edges
25" MIN.
25 1/4" MAX.
27 5/8" MIN.
28 1/8" MAX.
3/4" Support
Platform Required
Must Support 150 Lbs.
22" MIN.
Above
Support
Platform
Note: Oven is rated for use only under 30" standard or sealed burner gas and
selected 30" CleanDesign and Calrod
® electric cooktops.
Installation information: Before installing, consult installation instructions
packed with product for current dimensional data.
27"/24" built-in single oven dimensions (in inches)
27" models PK916, JKP70, JKP30, JKS10
2" x 4"
or equiv.
runners
B MIN.
C MIN.
Conduit 48-1/2" long
32-1/2
D
10
A
Allow 3/4"
for overlap
over all edges
of cutout
Locate
junction box
either 5" MIN.
below cutout
floor or 44"
MIN. above
cutout floor
Minimum
cutout location
from floor
(Minimum 15-5/8"
from floor when
installed below built-in
microwave oven)
E
G
F
20
Sealed burner gas cooktop
installation dimensions (in inches)
Standard burner gas cooktop
installation dimensions (in inches)
90 ° Street el
45 ° Elbow
Cabinet sides
2" Diameter hole (20-7/8"
from front of countertop
to hole center)
5" To center of 2" diameter
hole from countertop
90° Street el
45° Elbow
To center of 2" diameter
hole from countertop
Cabinet sides
3-7/16"
2" MIN. diameter hole
(23-1/4" from front
surface of countertop)
Note: Cabinets installed adjacent to wall ovens must have
an adhesion spec of at least a 194°F temperature rating.
Note: These ovens are not approved for stackable or side-by-side installations.
Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent
45° and 90° walls should be placed to avoid interference with the handle.
Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at
least a 194°F temperature rating.
Note: For 27" built-in single ovens, if marks, blemishes or the cutout opening is
visible above the installed oven, it may be necessary to add wood shims under the
runners and front trim until the marks or openings are covered.
Electric wall ovens are not approved for installation with a plug and receptacle.
They must be hard wired in accordance with installation instructions.
Note: 36" ribbon cooktops are approved for use over
GE 30" single wall ovens* and warming drawers. 30"
ribbon cooktops are approved for use over GE 30"
and GE 27" single wall ovens* and warming drawers.
Refer to cooktop and wall oven installation information
packed with products for current dimensional data.
*Except wall ovens with Trivection
® technology.
Oven support
for 27" models
Oven support
for 24" models
C L
Suitable
bracing
to support
runners
18"
Over centerline
of cabinet
2" x 4" or
equivalent
runners
(Must support 275 lbs.)
(Must support 275 lbs.)
CL
2 x 4 or
equivalent
runners
11"
over centerline
of cabinet
Cabinet PK916, JKP70/30, JKS10
A – Cabinet width required 27" min.
B – Minimum cabinet depth 23-5/8"
C – Opening width 25" min. - 25-1/4" max.
D – Opening height 27-5/8" min. - 28-1/8" max.
Oven
E – Overall depth* 23-5/8"
w/o trim 29"
F – Overall height with trim 29-7/8" - 30-3/4"
G – Overall width 26-5/8"
* Depth including door handle is approximately 26-7/8" min to
26-8/10" max. 26-5/8" on models PK916, JKP70/30 and JKS10.
47019_GE_59 59 47019_GE_59 59 2/6/07 4:34:18 PM 2/6/07 4:34:18 PM