Marantz DL5500 - Manual (Page 68)

PC MODE CONNECTION AND OPERATION
68
IMPORTANT: TURN OFF THE REAR PROJECTION TV/PC MONITOR AND THE PC BEFORE CONNECTING OR
DISCONNECTING ANY CABLES.
AUDIO OUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
RGB
OUTPUT
D-SUB 15 Pin
RGB Cable
(Optional)
Audio Cable
(Optional)
ANT A
TO
CONVERTER
ANT B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
AUDIO
L
R
(MONO)
VIDEO VIDEO
AUDIO
(MONO)
L
R
AUDIO
(MONO)
L
R
VIDEO
S-VIDEO S-VIDEO
Y
B
R P
B
R P
P
S-VIDEO
L
R
STOP
CONNECT ONLY 8 OHM SPEAKERS
DO NOT SHORT CIRCUIT
THESE TERMINALS
(Such damage is NOT COVERED
by your television warranty)
REAR SPEAKER 8 Ω ONLY
-
L
+
- +
R
PC 1
AUDIO
INPUT
MONITOR
OUT VIDEO 2 VIDEO 1
AUDIO OUT
L
R
SUB
WOOFER
OPTICAL COAXIAL
DIGITAL IN
P
Y Rear Panel of Television
REAR PANEL
CONNECTION TO PC
This PC ready Rear Projection Television can automatically detect and display PC signal format.
1. RGB input signal.
This PC ready Rear Projection Television can accept the following signal formats.
Preset Timings
No. Formats Horizontal No. Formats Horizontal
Frequency Frequency
1 VGA 640x400 70.1Hz 31.48kHz 13 XGA 1024x768 60.00Hz 48.36kHz
2 VGA 640x480 59.95Hz 31.48kHz 14 XGA 1024x768 70.07Hz 56.48kHz
3 Mac13 640x480 66.67Hz 35.00kHz 15 XGA 1024x768 75.03Hz 60.02kHz
4 VGA 640x480 72.81Hz 37.86kHz 16 Mac19 1024x768 74.93Hz 60.24kHz
5 VGA 640x480 75.00Hz 37.50kHz 17 XGA 1024x768 85.00Hz 68.68kHz
6 VGA 640x480 85.01Hz 43.27kHz 18 Mac21 1152x870 75.06Hz 68.68kHz
7 SVGA 800x600 56.25Hz 35.16kHz 19 SXGA 1280x1024 60.02Hz 63.98kHz
8 SVGA 800x600 60.32Hz 37.88kHz 20 SXGA 1280x1024 75.02Hz 79.98kHz
9 SVGA 800x600 72.19Hz 48.08kHz
10 SVGA 800x600 75.00Hz 46.88kHz
11 SVGA 800x600 85.06Hz 53.67kHz
12 Mac16 832x624 74.55Hz 49.72kHz
D-SUB 15 Pin
RGB Cable
(Optional)
PC
AUDIO OUT
Back of PC
Audio Cable
(Optional)
̇
VIDEO 3
VOL-
̇ ̇
AUDIO IN
VIDEO 3/PC2
L/(MONO) R VIDEO S-VIDEO
PC2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
INPUT VOL+ CH- CH+
TV/PC EXIT
MENU
̈ SELECT
FRONT PANEL
CONNECTION TO PC
NOTE: 1. Dots correspond to the true resolution in Real Mode of aspect ratio, when you select signal of No. 1 to No. 12 on the
table above. (One dot corresponds to one pixel).
2. The signal which resolution exceeds either 1280 dots or 720 lines may not display truly due to compression, then edges
of the picture are slightly hidden.
3. Both vertical and horizontal picture in full mode and vertical picture in normal mode are overscanned.
4. We recommend you change either refresh rate or resolution setting of your video card at control panel from 60Hz to
70Hz, if you see noise on the picture with XGA 60Hz.
5. Always reset AUTO ADJUST feature when setting new display setting (VGA,SVGA,XGA) or when changing to a new
computer.