Metabo Compressor Pump Classic 8 - Manual (Page 11)

11
ENGLISH
pressors, pressure vessels and air
tools.
A Hazard generated by oil-satu-
rated compressed air!
• Use oil saturated compressed air
only for air tools requiring such sup-
ply.
• Do not use an air hose used to sup-
ply compressed air containing oil to
supply air tools not designed for
operation on compressed air con-
taining oil.
• Do not fill tires with compressed air
containing oil.
A
Risk of burns from the sur-
faces of parts carrying compressed
air!
• Let tool cool off before servicing.
A Risk of personal injury and
crushing by moving parts!
• Do not operate the electric tool with-
out installed guards.
• Please note that the compressor will
start automatically when the pres-
sure falls off to minimum! – discon-
nect from power supply prior to any
servicing.
• Ensure that when turning ON (e.g.
after servicing) no tools or loose
parts are in the electric tool.
A Hazard generated by insuffi-
cient personal protection gear!
• Wear hearing protection.
• Wear safety glasses.
• Wear mask respirator when work
generates dust or mist detrimental
to health.
• Wear suitable work clothes. When
working outdoors wearing of non-
slip shoes is recommended.
A Hazard generated by electric
tool defects!
• Do not make changes to the com-
pressor. Any modification to pres-
sure-carrying components renders
the type examination test null and
void. Repairs to compressors and
air tools must be carried out by
authorised specialists only.
• Keep electric tool and accessories
in good repair. Check and service
the compressor periodically.
Observe the maintenance instruc-
tions.
• Priot to any use check the electric
tool for possible damage: before
using the electric tool carefully
check safety devices, protection
devices or slightly damaged parts
for proper function as specified.
• Check to see that all moving parts
work properly and do not jam. All
parts must be correctly installed and
meet all conditions necessary for
the proper operation of the electric
tool.
• Damaged protection devices or
parts must be repaired or replaced
by a qualified specialist.
• Have damaged switches replaced
by a service centre.
• Do not operate electric tool if the
switch can not be turned ON or
OFF.
• Keep handles free of oil and grease.
3.3 Symbols on the machine
Danger!
Neglect of the following
warnings may cause seri-
ous injury or material
damage.
Read instructions.
Information on the nameplate
3.4 Safety Devices
Safety valve
The spring safety valve (26) is incorpo-
rated into the pressure switch unit. The
safety valve opens if the max. permissi-
ble pressure is exceeded.
Check condensate drain
• Check to see that the condensate
drain's screw (27) is closed.
4.1 Installation
The place of installation must meet the
following requirements:
• dry, cool, protected from freezing
• firm, level and even ground
A
Danger!
Incorrect installation can cause bad
accidents.
• Secure compressor against mov-
ing away and tipping over.
• Do not pull compressor by air
hose or power supply cable.
• Safety devices and operator's
controls must be readily accessi-
ble at all times.
(11) Manufacturer
(12) Item no., version no., serial no.
(13) Machine designation
(14) Supply voltage / frequency
(15) Motor capacity P
1
(see also “Technical Specifica-
tions”)
(16) Fuse protection / protection class
(17) No. of cylinders
(18) Motor speed
(19) Suction capacity
(20) Filling rate
(21) Speed compressor pump
(22) Max. pressure
(23) Pressure vessel volume
12
13
14
15
16
11
18
20
21
22
23
17
19
24
25
(24) Year of make
(25) CE-mark – This machine complies
with the EU Directives as per dec-
laration of conformity
4. Operation
26
27