Miller Electric Engine-Driven Welder/ AC Generator/Air Compressor - Manual (Page 4)

4
Genuine Miller ® Accessories
Desiccant Air Dryer System #195 117
A regenerating inline air dryer system that
eliminates moisture in the air stream to
prevent air tool freeze-ups in cold climates.
Internal thermostat and heating elements
insure good air quality in all climates.
The system can be mounted on the side
of the machine or remotely for truck
mount installations.
AC/DC/Battery Charge/Jump-Start Switch
#195 148 Field
AC TIG welding and 12/24-volt battery
charge/jump-starting system.
Weld Ammeter and Voltmeter
#195 131 Field
Panel-mounted AC/DC analog meters to
monitor weld output.
U.S. Model Full KVA
Plug Kit #119 172 Field
1-phase, 120/240 VAC, 50 A
plug (NEMA 14-50P) to fit
full KVA receptacle.
International Plug
#255 416 Field
1-Phase, 240 VAC, 16 A plug
Cold Weather Starting Kit*
#195 086 Field
120 V oil pan heater element.
Engine Filter Kit #246 988 Field
Includes all filters required for proper
engine maintenance. Oil filter, primary and
secondary fuel filter, and primary air filter.
Compressor Filter Kit #246 991 Field
Includes all filters required for proper
compressor maintenance. Oil filter, air filter
and coalescing filter.
FA-1D Lockable Flame Arrestor
Fuel Cap #043 947 Field
Fuel cap can be padlocked to
prevent vandalism. A built-in
flame arrestor prevents flames
or sparks from entering the
fuel tank.
Vandalism
Lockout Kit
#195 118 Field
Lockable hinged
steel panels cover
and protect name
plate gauges and
ignition switch
(padlock included).
Also includes engine
compartment door
lock and key.
Cable Holder
#043 946 Field
Saddle-bag-style
cable holder.
Convenient wrap-
around storage of
coiled cable for
transportation.
Stores 100 feet
of 2/0 cable on
each side.
Note: For best results do not weld when cable is coiled!
Protective cover cannot be used with cable holder.
Protective Cover
#194 683 Field
Blue water-resistant
canvas cover resists
stains and mildew,
and protects the
finish of your welder.
Note: Protective cover cannot be used with cable holder.
Stick (SMAW) Welding
Weld Leads
2/0 Stick Cable Set, 50 ft. (15 m)
#173 851
Consists of 50-foot (15 m) 2/0 electrode
cable with holder, and 50-foot (15 m) work
cable with clamp. 350 A, 100% duty cycle.
2/0 Stick Cable Set, 100/50 ft. (30.5/15 m)
#043 952
Consists of 100-foot (30.5 m) 2/0 electrode
cable with holder, and 50-foot (15 m) work
cable with clamp. 300 A, 100% duty cycle.
MIG/Flux-Cored Welding
SuitCase ® X-TREME ™ 8VS Wire Feeder
#951 182
SuitCase
® X-TREME ™ 12VS Wire Feeder
#951 184
Lightweight, portable, voltage-sensing
wire feeders include secondary contactor
and gas valve and drive roll kit. See Lit.
Index No. M/6.41.
SuitCase ® 8RC Wire Feeder #951 186
SuitCase ® 12RC Wire Feeder #951 188
Lightweight and flexible enough to run a
variety of wires up to .062-inch diameter.
Includes remote voltage control and drive
roll kit. See Lit. Index No. M/6.5.
Spoolmatic ® 30A Spool Gun #130 831
Air-cooled, 200-amp, 1-pound spool gun for
aluminum MIG. See Lit. Index No. M/1.73.
WC-24 Control #137 549
Use with Spoolmatic 30A.
XR ™ Wire Feeders and Guns
Push-pull system designed to handle
difficult-to-feed soft alloy wires such as
aluminum. See Lit. Index No. M/1.7,
M/1.71, and M/1.73.