Miller Electric CST 280 - Manual (Page 3)

3
TIG (GTAW) Torches
Weldcraft ® TIG Torches
The Weldcraft line of TIG torches complements
the most popular TIG power source line
available today. The Weldcraft torch line
includes both air-cooled and water-cooled
models. Available with genuine Weldcraft parts.
#WP-17V-12-2 150 A, 12 ft (3.7 m)
air-cooled torch with valve, two-piece cable.
#WP-17V-25-2 150 A, 25 ft (7.6 m)
torch with valve, two-piece cable.
#WP-26V-12-2 200 A, 12 ft (3.7 m)
air-cooled torch with valve
#WP-26V-25-2 200 A, 25 ft (7.6 m)
air-cooled torch with valve
These two-cable TIG torches require the installation of a
Dinse Connector (042418) or Tweco Style Connector
(195115) depending on the CST Model Connector Type.
Remote Controls
RCC-14 Remote Contactor and Current
Control* #151 086 14-pin plug
Side-to-side rotary-motion fingertip control
fastens to TIG torch using two Velcro
®
straps. Includes 28 ft (8.5 m) control cord.
Great for production or contractors that
need quick ramp-up.
RCCS-14 Remote Contactor and Current
Control* #043 688
Up-and-down rotary-motion fingertip
control fastens to TIG torch using two
Velcro
® straps. Includes 28 ft (8.5 m)
control cord. Great for applications that
require a finer amperage control.
RFCS-14 Foot Control* #043 554
Foot pedal provides remote current and
contactor control. Includes 20 ft (6 m) cord
and 14-pin plug.
RHC-14 Hand Control* #129 340
Miniature hand control for remote current
and contactor control. Dimensions: 4 x 4 x
3-1/4 in (102 x 102 x 82 mm). Includes
20 ft (6 m) cord and 14-pin plug.
RFCS-14 HD Foot Control* #194 744
For all Miller solid-state power sources
after serial number JK674521. This new
design increases stability with a larger
base, and durability with a heavier cord.
Maximum flexibility is accomplished with a
reconfigurable cord that can exit the front,
back or either side of the pedal. Foot pedal
provides remote current and contactor
control. Includes 20 ft (6 m) cord and
14-pin plug.
*Note: The remote controls provide amperage control
only on the CST 280, no remote contactor control.
Genuine Miller Accessories
Cable Connectors and Adapters
Note: The Dinse version of the CST 280 includes one
set of male connectors. The tweco version does not.
International-Style Connector
#042 418 50 mm
Accepts #1 or #2 AWG cable size. Required
if male plugs shipped with power source must
be replaced or if additional plugs are needed.
Kit includes one International-style male
plug which attaches to the work and/or
weld cables and plugs into the International-
style recep tacles on the power source.
Extension Kit for International-Style
Cable Connectors #042 419 50 mm
Accepts #1 or #2 AWG size cable. Used to
adapt or extend weld and/or work cables.
Kit includes one male International-style
plug and one in-line female International-
style receptacle.
International/Tweco ®
Adapter #042 465
A one-piece adapter
which has an
International-style male
plug (to power source)
on one end and a female Tweco receptacle
(for weld cable connection) on other end.
International/Cam-Lok
Adapter #042 466
A one-piece adapter
which has an
International-style
male plug (to power source) on one end
and a Cam-Lok receptacle (for weld cable
connection) on other end.
Tweco/Dinse Adapter
#195 116
A one-piece adapter
which has a Tweco-
style male plug (to
power source) on one end and a female
Dinse or International-style receptacle (for
weld cable connection) on other end.
Tweco-Style
Connector
50 mm
#195 115
Accepts #1 or
#2 AWG cable
size. Kit includes one Tweco-style male plug
which attaches to the work and/or weld
cables and plugs into the receptacle on
the power source.