Melissa 758-007 - Manual (Page 15)

Installation Instructions
1. Remove all packing materials carefully. Please note,
that plastic bags can be dangerous toys for children !
2. The water inlet hose from the machine terminates in a
3/4” female connector. The water supply should
therefore terminate in a similar male connector and
must have a stopcock close by in the pipe. Connect the
straight connector of the inlet hose to the water supply
securely. Connect the other end (bent connector) to the
water inlet valve at the back of the dishwasher cabinet.
Do not over-tighten to avoid damage to threads.
3. Prepare the drainage hose so that it has hooked end.
Use the plastic U-bend fitting provided for this purpose.
The end of this should be dropped into a drainage
standpipe, the maximum height of which should be no
more than 15 cm above the base of the dishwasher. To
allow for an air gap around the end of the drain hose,
the diameter of the standpipe should be at least 30 mm.
Connect the other end of the drain hose (L shaped) to
the drain port connection at the back of the dishwasher
cabinet. Tighten the drain hose end on to the drain port
using the metal clip included in the package.
4. If you so wish, you may connect the water inlet hose on
to the kitchen sink tap. You must obtain correct
fittings/adaptors to match the inlet hose connectors to
ensure secure connection. However, permanent
plumbing is recommended.
NOTE: All plumbing work must be carried out by
authorised plumber.
5. If leaks are located, immediately shut power and the
water supply and check the hose connections fully.
Tighten connections if necessary.
6. If for any reason you are unable to stop the leak
yourself please seek advice from a qualified plumber.
7. The minimum height clearance required to install your
dishwasher on a countertop surface with overhead
cupboards is 50 cm.
8. Make sure there is an electrical power supply within
easy reach of the machine. The power cord is 180 cm
long.
9. The dishwasher must be installed on a ‘solid’ level
surface.
10. To level the dishwasher, adjust the 4 level screws (feet)
under the dishwasher.
11. Ensure that no hoses or cables are squeezed or
damaged by unit or other items.
Water Pressure
For best operating results, incoming water pressure should
be between 0,3 and 10 bar.
Electrical Instructions:
An electrical supply of 220-240 volts AC only, 50Hz is
required. Make sure that a suitable electrical supply socket is
located close to where the dishwasher is to be placed. The
appliance Must be earthed. The appliance is equipped with a
power supply cord having a 3-pin grounding plug. To
minimize possible shock hazards it must be plugged into a
matching 3-pin grounding type electrical outlet. The electrical
outlet should be easy accessible. Fixed connection to the
mains supply, must be made by an authorised electrician.
If the mains plug is unsuitable for the socket outlet in your
home or is removed for any other reason, then the cut off
plug should be disposed of safety to prevent the hazard of
electric shock.
FOR BEST RESULTS:
Your dishwasher cleans by spraying a mixture of hot clean
water and detergent (under pressure) against the soiled
surface of dishes. The water is pumped through a rotating
spray arm, drained through a filter removing food and soiled
particles and pumped back through the spray arm. Soiled
water is pumped out and replaced with clean water at the
end of each cycle (the number of times depends on the cycle
being used). For best cleaning results, the water temperature
must be at least 55°C. To prevent dishwasher damage, the
temperature of the incoming water supply should not exceed
65°C. NOTE: Hard Water conditions will adversely affect
wash ability performance of your dishwasher. Hard Water
conditions will also contribute to “Lime” (white film
substance) deposits and/or “Scaling” on the stainless steel
surface of the dishwasher tub and “Heater Element” located
in the sump underneath the removable filter screen. To assist
in minimizing these conditions, it is recommended to
periodically operate/rinse the inside of the dishwasher
(empty) using 1 cup of white vinegar (at least once a week).
Disconnecting your Dishwasher
- Close the water supply at the stopcock.
- Disconnect the power supply cord. Do not pull cord, but
use plug only when removing. Alternatively remove fuses
from buildings electrical fuse board.
- Disconnect the inlet hose assembly from the water supply.
When the dishwasher is not in use, place/store the hose on
the hanger hose bracket located on the rear wall of the
dishwasher cabinet.
- Appliances that are to be discarded must be made
unusable. Pull off the plug, remove cable and make the door
lock and latch unusable
! IMPORTANT !
Once you open the water supply line, (even if it is closed
immediately thereafter) the water inlet hose will be
pressurized.
! CAUTION !
DO NOT LET CHILDREN DISCONNECT THE
DISHWASHER. Close supervision of children is always
important around appliances.
15
758007_IM_new 03/02/06 12:56 Side 15