Memorex MVT2140 - Manual (Page 21)

21
ENGLISH
When either the F.FWD or REW button is pressed in the
PLAYBACK mode, the speed search picture will appear.
When pressed twice, the search picture will increase
speed. Speed search time depends upon the speed
used (SP, LP or SLP) during recording. See chart below.
To visually search backward or forward, press the REW
or F.FWD button once or twice in the PLAYBACK mode.
Press the PLAY button to resume normal viewing speed.
SPEED SEARCH TIMES
NOTES: • The audio output is muted during Speed
Search and Still.
• A few noise bars will appear on the TV screen
during Speed Search and Still.
• To prevent damage to the tape, Still and Speed
Search mode is automatically changed to the
Playback mode after 5 minutes.
Press the PAUSE/STILL button in the PLAYBACK mode.
Press the PLAY button or PAUSE/STILL button to resume
normal playback.
Press the SKIP SEARCH button in the PLAY mode. The VCR
will search forward through approximately 30 seconds of the tape
(e.g. unwanted commercial time) for each press of the SKIP SEARCH
button (maximum six presses) and then resume normal playback.
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈 +/–/ENTER/MENU 〉
1 Press the MENU button.
2 Press the SET/TRACKING + or
– button to select the AUTO
REPEAT option.
3 Press the ENTER button to select
the ON position.
NOTE: To cancel repeat mode, follow above steps 1 and
2, then press the ENTER button to select the OFF
position. Press the MENU button to return to the
TV. The repeat function is canceled automatically
when the unit is switched off or the tape is ejected.
1 Load a cassette tape with the erase prevention tab
intact.
2 Press the SPEED button to
select the desired tape speed
SP or SLP. The counter and SP
or SLP will appear on the screen
about 4 seconds.
3 Set the TV/CATV option to the appropriate position
(See page 16).
00:00:00 SP
NOTES: • If power is switched off during recording,
the TV set goes off and the VCR continues
to record. Press the STOP button to halt
the recording and turn off the VCR.
• The TV/VCR Channel cannot be changed
during recording.
CH 012
Press the PAUSE/STILL button to avoid recording
unwanted material.
“
” will appear on the screen and the REC/OTR
indicator will blink on and off. Press the PAUSE/STILL
button or the REC/OTR button to continue the recording.
NOTE: The PAUSE mode will be changed to STOP mode
after five minutes to prevent damage to the tape.
Press the STOP button to stop recording.
“
■ ” will appear on the screen.
NOTES: • AUTO REWIND FEATURE
This TV/VCR will automatically rewind the video
cassette when the tape has ended (except
during OTR and Timer Record). It will also eject
the video cassette.
• If the erase prevention tab is removed, the tape
will eject when the REC/OTR button is pressed
for recording.
SPECIAL PLAYBACK
TO VISUALLY SEARCH FOR DESIRED
POINTS
PICTURE SEARCH SPEED
PRESS TWICE
TAPE SPEED
PRESS ONCE
SP (Standard Play)
LP (Long Play)
SLP (Super Long Play)
SKIP SEARCH
TO WATCH STILL PICTURE
TO WATCH A TAPE REPEATEDLY
RECORDING A TV PROGRAM
RECORDING AND VIEWING THE
SAME TV PROGRAM
TV - VHF/UHF channels
CATV - CABLE TV channels
4 Press the Direct Channel Selection buttons or
CHANNEL Up or Down button to select the channel
to be recorded.
5 Press the REC/OTR button.
"
● " and the channel number will
appear on the screen and the
REC/OTR indicator will light.
TO STOP RECORDING
TO STOP RECORDING TEMPORARILY
4 Press the MENU button. If you press the PLAY button,
the tape will play over and over until the repeat mode is
canceled.
PRESS TWICE PRESS ONCE
5 X
9 X
15 X
3 X
7 X
9 X
5A3B201A E P20-Back 11/4/02, 12:43 PM 21