MSB Technology DVD Audio Player - Manual (Page 41)

41
S
UPER
DVD A
UDIO
P
LAYER
S
PECIFICATIONS
I NPUTS : 8 L INE L EVEL RCA I NPUTS
(5V
RMS MAXIMUM
)
C OMPOSITE V IDEO
S V IDEO
YUV V IDEO
A UDIO O UTPUTS : 8 VOLUME CONTROLLED
RCA
OUTPUTS
(5 V
RMS
M AX )
5.1 CHANNEL L INE LEVEL
DB-25 OUTPUT
B ALANCED L INE LEVEL
XLR
FRONT ONLY
interrupted momentarily when this happens.
LOOP CONNECT - The IEEE1394 network cannot function because it is connected in a loop.
BUS FULL - The IEEE1394 bus has reached its capacity and cannot transmit any more data.
Limited Warranty
All MSB products carry a one year warranty from the original retail purchase date, or a two year warranty from the original date sold to a
dealer, which ever is first.. MSB warrants that products distributed by MSB in the USA that fail to function properly under normal use due
to a manufacturing defect when installed and operated according to the operating instructions enclosed with the unit will be repaired or
replaced with a unit of comparable value at the option of MSB without charge to the customer for parts or actual repair work. Parts supplied
under this warranty may be new or rebuilt at the option of MSB. This warranty covers the product during the period whether in the
possession of the original owner or any subsequent owner. In the event service is required, the product must be delivered within the
warranty period, transportation prepaid, from within the US. The customer will be responsible for removal and installation of the product.
This warranty does not cover any product which is used in any trade or business, or in an industrial or commercial application. This
warranty does not cover damage to discs, damage resulting form alterations, modifications not authorized in writing by MSB, accident,
misuse or abuse, damage due to lightning or to power surges, subsequent damage from leaking, damaged or inoperative batteries or the use
of batteries not conforming to those specified in the operating instructions. This warranty does not cover the cost of parts and repair
which would be otherwise provided without charge obtained from any other source, or damage caused by the use of unauthorized parts
or labor, or from improper maintenance. Altered, defaced or removed serial numbers void this warranty. MSB excludes any obligation on
its part for incidental or consequential damages related to the failure of products to function properly under the conditions set for above.
MSB limits its obligation under any implied warranties including but not limited to the impled warranties of merchantability and fitness for
a particular purpose to a period not to exceed the warranty period. No warranties shall apply after the warranty period. This warranty gives
you specific rights, the customers rights may vary from state to state.
If you have a failure, call MSB and describe the problem. If no solution is possible, the product must be boxed in the original or equivalent
packaging and returns to MSB. No returns are accepted without an RMA number. Upon receipt, MSB will repair or replace any defective
product. MSB will return the product at MSBs expense in the packaging supplied. Shipping damage is the responsibility of the consignee.
Care and Placement of the Player
Cleaning the lens is not recommended as you may damage the lens. Condensation can be a problem if you bring the player into a warm
room from the outside. Do not use the player for at least an hour. Your player generates quite a bit of heat. DO NOT BLOCK THE
VENTILATION SLOTS IN THE COVER. Be sure it is placed on a hard surface so air can pass under the product. Do not place in a cabinet
with amplifiers without proper ventilation. Do not place on top of any other product which gets warm. Do not use in dusty, damp or
locations exposed to the sun. Do not move or bump the player when a disc is spinning. Do not transport the player with a disc in it.
Upgrades and Modifications
Removal of the cover - Unplug the AC power. Work on a soft scratch resistant surface like a carpeted floor. Start with the unit upside down
and remove three screws located along the front edge of the cover. Then turn the unit over and remove the three screws along the back
edge of the cover. Loosen the four screws holding the endcaps on as they may prevent the cover from moving easily. Slide the cover
toward the front of the unit and lift off. Turn and place on its face carefully as a cable is attached. Place a box or object for the cover to lean
on. Now the upgrades may be installed or the settings changed.
D IGITAL O UTPUTS : C OAXIAL
O
PTICAL
MSB N ETWORK
IEEE 1384
A TTENUATION R ANGE : -70 D B TO +10 D B
S
TEP
S
IZE
: 1
D
B
PER STEP
T RIM R ANGE : 26 D B IN 1 D B SIZE STEPS
D
YNAMIC
R
ANGE
: 103 dB
THD+N: .002%
S
IGNAL TO
N
OISE
R
ATIO
: 103 dB
C
HANNEL
S
EPARATION
: 110 dB
P
OWER
C
ONSUMPTION
: W