Line drawing best fitting for ug – Motorola Two Way Radio KEM-ML36801A User Manual
Page 2
MENU
MD Series
Products Covered
Products and Accessories as
defined above, unless otherwise
provided for below.
1. Consumer Two-Way Radio
Accessories.
2. Products and Accessories
that are Repaired or
Replaced.
Length of Coverage
One (1) year from the date of
purchase by the first consumer
purchaser of the product unless
otherwise provided for below.
1. Ninety (90) days from the
date of purchase by the first
consumer purchaser of the
product.
2. The balance of the original
warranty or for ninety (90)
days from the date returned
to the consumer, whichever
is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded from
coverage.
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper
operation, storage, misuse or abuse, accident or neglect, such as
physical damage (cracks, scratches, etc.) to the surface of the
product resulting from misuse; (b) contact with liquid, water, rain,
extreme humidity or heavy perspiration, sand, dirt or the like, extreme
heat, or food; (c) use of the Products or Accessories for commercial
purposes or subjecting the Product or Accessory to abnormal usage
or conditions; or (d) other acts which are not the fault of Motorola
Solutions, Inc. or Giant International Ltd., are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects
or damage that result from the use of Non-Motorola branded or
certified Products, Accessories, or other peripheral equipment are
excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by someone
other than Motorola Solutions, Inc., Giant International Ltd. or its
authorized service centers, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers
or date tags that have been removed, altered or obliterated; (b)
broken seals or that show evidence of tampering; (c) mismatched
board serial numbers; or (d) nonconforming or non-Motorola
branded housings, or parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of
Products or Accessories due to any communication service or
signal you may subscribe to or use with the Products or Accessories
is excluded from coverage.
Warranty
Consumer Two-Way Radio Products and Accessories purchased in
the United States and Canada.
What Does this Warranty Cover?
Subject to the exclusions contained to the right, Giant International
Ltd. warrants the Motorola branded consumer two-way radios that
operate via Family Radio Service or General Mobile Radio Service
that it manufactures (“Products”) and the Motorola branded or
certified accessories sold for use with these Products that it
manufactures (“Accessories”) to be free from defects in materials
and workmanship under normal consumer usage for the period(s)
outlined below. This limited warranty is a consumer’s exclusive
remedy, and applies as follows to new Motorola branded Products
and Accessories manufactured by Giant International Ltd., and
purchased by consumers in the United States and Canada, which
are accompanied by this written warranty:
Who is covered?
This warranty extends only to the first consumer purchaser, and is
not transferable.
What will GIANT INTERNATIONAL LTD. do?
GIANT INTERNATIONAL LTD., at its option, will at no charge repair,
replace or refund the purchase price of any Products or
Accessories that does not conform to this warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned or
new Products, Accessories or parts.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
USA and Canada Two-Way Radios
1-800-638-5119
For Accessories, please call the telephone number designated
above for the product with which they are used.
You will receive instructions on how to ship the Products or
Accessories at your expense, to a GIANT INTERNATIONAL LTD.
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL
MOTOROLA SOLUTIONS. INC. OR GIANT INTERNATIONAL LTD. BE
LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE
OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR OTHER FINANCIAL LOSS ARISING OUT
OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE
THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion
of incidental or consequential damages, or limitation on the length of
an implied warranty, so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state or from one
jurisdiction to another.
Patent and Copyright Information
Manufactured, distributed or sold by Giant International Ltd., official
licensee for this product. MOTOROLA, MOTOROLA SOLUTIONS and
the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All
other trademarks are the property of their respective owners. ©2012
Motorola Solutions, Inc. All rights reserved.
Special Features
Keypad Lock
To avoid accidentally changing your radio settings you can lock your
keypad:
1. Press and hold until displays.
2. When in lock mode, you can turn the radio on and off, receive,
transmit, send a call tone, and monitor channels. All other functions
are locked.
To unlock the radio, press and hold for a few seconds until no
longer displays.
Scanning Channels
Use scan to search the 22 channels for transmissions from unknown
parties, to find someone in your group who has accidentally changed
channels, or to quickly find unused channels for your own use.
To start Scanning:
1. Briefly press the
key. The scan
will appear in the display, and the
radio will begin to scroll through the channel.
2. When the radio detects channel activity matching the channel, it
stops scrolling and you can hear the transmission.
3. To respond and talk to the person transmitting, press
within five
seconds after the end of the transmission.
4. The radio will resume scrolling through the channels five seconds
after the end of any received activity.
5. To stop scanning, briefly press the
key.
Scanning Notes
1. If you press
while the radio is scrolling through inactive
channels, the transmission will be on the “home channel”. Scanning
will resume five seconds after the end of your transmission. You may
press the
key to stop scanning at any time.
2. If the radio stops on an undesired transmission, you may
immediately resume the scan by briefly pressing
or
.
3. If the radio repeatedly stops on an undesired transmission, you may
temporarily remove that channel from the scan list by pressing and
holding
or
for three seconds. You may remove more than one
channel in this way.
4. To restore the removed channel(s) to the scan list, turn the radio off
and then back on, or exit and re-enter the scanning mode by
pressing
.
5. You cannot remove the home channel from the scan list.
Use With Accessories
You can transmit more reliably with the use of optional PTT headset
accessories. A PTT headset allows privacy to others around you while
listening.
Many accessories (sold separately) are available for your radio. For
more information, visit our Web site at www.motorolasolutions.com or
shop.giantintl.com.
1. Turn the radio off and plug the PTT accessory into the accessory
jack.
2. Turn the radio on. You may now press the PTT on the accessory
microphone instead of the radio.
3. Adjust the volume appropriately by pressing
. Lower the volume
before placing the accessory on your head or in your ear.
Note: The MD Series does not have VOX capabilities, and is only
compatible with PTT headset accessories.
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
MENU
MENU
MENU
MENU
MENU
MENU
MENU
MENU
MENU
MENU
Menu Options
Selecting the Channel
Your radio has 22 channels. The channel is the frequency your radio
uses to transmit. (See Channels and Frequencies table below.)
1. Briefly press and release
. The channel number flashes.
2. Press
or
to select a channel.
3. Press to confirm or
to continue set up.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group
so you can alert them that you want to talk. You have 10 call tones from
which to choose.
To set a call tone:
1. With the radio on, short press
until the appears. The current call
tone setting flashes.
2. Press
or
to change and hear the call tone.
3. Press to set the new call tone or
to continue set up.
To transmit your call tone to other radios set to the same channel as
your radio, press .
Note: Setting the call to 0 disables the call tone feature.
Transmitting a Talk Confirmation Tone
You can set your radio to transmit a unique tone when you finish
transmitting. It is like saying “Roger” or “Over” to let others know you
are finished talking.
1. With the radio on, short press until appears. The current
setting On/Off flashes.
2. Press
or
to turn On or Off.
3. Press to set the talk confirmation tone or
to continue
set up.
Keypad Tones
You may enable or disable the speaker key tones. You will hear the key
tone each time a button is pushed.
1. Press until appears. The current setting On/Off will flash.
2. Press either
or
to turn On or Off.
3. Press to confirm or
to continue set up.
Note: When the key tone feature is off, the following are not disabled:
• Transmit timeout alert tone
• Power-down alert tone
• Low battery alert tone
• The transmitted talk confirmation tone
Auto Power Off
Your radio will save power by automatically turning itself off if unused
after a predetermined amount of time.
1. Activate this setting by short pressing
until displays. The current
setting (0, 30, 60, 90) will flash.
2. Press
or
to set the time to 30 minutes, 60 minutes or
90 minutes.
3. When you exit the Menu mode, the setting timer will begin if you are
not using the radio.
4. The screen shows .
5. Press to confirm or
to continue set up.
Channel
Frequency
(MHz)
Description Channel
Frequency
(MHz)
Description
1
462.5625
GMRS/FRS
12
467.6625
FRS
2
462.5875
GMRS/FRS
13
467.6875
FRS
3
462.6125
GMRS/FRS
14
467.7125
FRS
4
462.6375
GMRS/FRS
15
462.5500
GMRS
5
462.6625
GMRS/FRS
16
462.5750
GMRS
6
462.6875
GMRS/FRS
17
462.6000
GMRS
7
462.7125
GMRS/FRS
18
462.6250
GMRS
8
467.5625
FRS
19
462.6500
GMRS
9
467.5875
FRS
20
462.6750
GMRS
10
467.6125
FRS
21
462.7000
GMRS
11
467.6375
FRS
22
462.7250
GMRS
Channels and Frequencies
PTT
PTT
PTT
PTT
PTT
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_
Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
MD_Series_US.qxd:Layout 1 2/6/12 12:25 PM Page 2