Murphy SWICHGAGE 45TEBP - Manual

SPL-92106N page 1 of 4
Installation for 4- 1 /
2
in. (114 mm) dial
Temperature MURPHYGAGE ® and SWICHGAGE ®
SPL-92106N
Revised 04-04
Section 10
(00-02-0167)
SPLC and SPLFC SWICHGAGE ® instruments have high
and low limit contacts to monitor, alarm or shutdown. The SPLC
has a flanged case. SPLFC has a flush mount case intended for
installation within a panel. A method to override the low limit
contact for startup is provided on most models (see Operation
Test Instructions on page 3).
45TE and 45TEF Series are versions of the SPL Series
with 2-snap acting SPDT switches instead of the pointer type con-
tacts. The 45TE Series does not include low contact lockout.
SPLBP and 45TEBP models are designed to start and stop
electric motor driven equipment. The pilot duty contacts are con-
nected to a latching control relay for automatic ON/OFF control,
either directly or through a motor starter.
Options -OS and -ES
The -OS (oil sealed case) and the -ES (environment sealed case)
options for corrosive environment feature flush mount case design
to be installed within a panel.
Precautions
■ Do NOT exceed rated temperature range.
■ Use shock mounts as necessary to protect from vibration.
■ Cutting or sharp bending the capillary will cause permanent
damage to the SWICHGAGE
® and will void the warranty.
■ Excess capillary should be carefully coiled and secured
away from damage.
■ Do not route capillary along exhaust manifold.
■ Avoid routing capillary at level higher than gage mounting.
Please read the following instructions before installing . A visual inspection is recommended before mounting.
General Information and these installation instructions are intended for all 4-1/2 in. (114 mm) dial temperature models.
GENERAL INFORMATION
Accuracy
15 to 250°F ± 8°F ± 2°F ± 2°F
(9 to 121°C) (± 4°C) (± 1°C) (± 1°C)
130 to 350°F ± 8°F ± 2°F ± 3°F
(54 to 177°C) (± 4°C) (± 1°C) (± 1.5°C)
260 to 450°F ± 8°F ± 2°F ± 3°F
(127 to 232°C) (± 4°C) (± 1°C) (± 1.5°C)
Temperature Range Lower 1 /
4 Middle 1 /
2 Upper 1 /
4
Model Series: SPLG, SPLC, SPLBP, 45TE and 45TEBP
Options: -OS and -ES
WARNING
BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT
✔
Disconnect all electrical power to the machine.
✔
Make sure the machine cannot operate during installation.
✔
Follow all safety warnings of the machine manufacturer.
✔
Read and follow all installation instructions.
®
*
**
* Selected configurations are CSA approved. Consult factory for details.
** Products covered by this literature comply with EMC Council directive 89/336/EEC
regarding electromagnetic compatibility as noted. Does not cover “BP” models.
Specifications
Dial: White on black, dual scale, °F and °C standard,
4-1/2 in. (114 mm) diameter.
Case: Die cast aluminum, surface or panel mount.
Capillary: PVC armored copper tube, 5 ft. (1.5 m) long standard.
Sensing Bulb: Copper bulb std.: 1/2 in. (13 mm) OD;
Length 7 in. (178 mm). Pressure rating: 600 psi (4.1 MPa)
[41 bar]. Connection: 1/2 NPTM compression fitting.
NOTE: Use of thermowell is highly recommended.
Switch Reset Deadband: Approximately 10% FS.
Snap-Acting Switches: See wiring information (page 4).
Dry Relay Contact (“BP” Models): 10 A @ 28 VDC or
10 A @ 120 VAC.
Wire Connections (Surface Mount): 1/2 NPTF conduit/terminal block.
Wire Connections (Panel Mount): Wire leads, 18 AWG
(1.0 mm2) x 9 in. (229 mm) long.
Wire Connections (-ES, -OS, -CC): 1/2 NPTM conduit and wire leads,
24 AWG (0.22 mm2) x 33 in. (838 mm) long.
Overrange: Do not exceed 10% FS above full range.
Item Weight: 8 lbs (3.6 kg) approx. Explosion-proof models: 22 lb.
(10 kg) approx.
Item Dimensions: 16 x 11 x 5-1/2 in. (406 x 279 x 140 mm)
approximately. Explosion-proof: 12 x 12 x 9 in. (305 x 305 x 229 mm)
approximately.