Maxus MXN102 - Manual (Page 4)

6 Rotate door back
into the closed
position.
7. Push button
down
again to lift the
hook. Close the
door and release
the button to
reengage the hook with the nose.
8. Make sure the trig-
ger and work contact
element (WCE) move
freely up and down
without sticking or
binding.
Technical Support
Please call our Nailer Hotline at 1-888-
241-5858 with any questions regarding
the operation or repair of this nailer or
for additional copies of this manual.
Fastener And Replacement
Parts
Use only 18
gauge fasteners
(see Fastener Interchange Information).
Tool performance, safety and durability
could be reduced if improper fasteners
are used. When ordering replacement
parts or fasteners, specify by part num-
ber.
! WARNING
Operating The Nailer
(Continued)
ADJUSTING THE DIRECTION OF THE
EXHAUST
The nailer is
equipped with an
adjustable direc-
tion exhaust
deflector. This is
intended to allow the user to change
the direction of the exhaust. Simply
twist the deflector to any direction
desired.
CLEARING A JAM FROM THE NAILER
1. Disconnect the
air supply from
the nailer.
2. Remove all nails
from the maga-
zine (see
Loading/
Unloading).
Failure to remove
all fasteners will
cause the fasteners to eject from the front
of the tool.
3. Undo hook by
pushing down on
the button on the
side of the maga-
zine. The button
will disengage the hook from the
nose.
4. The door can now
be rotated, expos-
ing the jammed
fastener.
5. Remove the
jammed fas-
tener, using
pliers or a
screwdriver if
required.
! WARNING
Nailer Repair
Only qualified personnel shall repair
the tool and they shall use genuine
Maxus replacement parts and acces-
sories, or parts and accessories which
perform equivalently.
Assembly Procedure For
Seals
When repairing a nailer, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots.
MXN102 Operating Instructions
5
Rotate
Operating The Nailer
(Continued)
OPERATIONAL MODE
Always know the
operational mode
of the nailer before using. Failure to
know the operational mode could
result in death or serious personal
injury.
SINGLE SEQUENTIAL MODE
This mode
requires the trig-
ger to be pulled
each time a nail
is driven. The nailer can be actuated by
depressing the WCE against the work
surface followed by pulling the trigger.
The trigger must be released to reset
the tool before another nail can be dri-
ven.
OPERATING A SEQUENTIAL TRIP
NAILER
Check the opera-
tion of the Work
Contact Element (WCE) trip mechanism
before each use. The WCE must move
freely without binding through its
entire travel distance. The WCE spring
must return the WCE to its fully extend-
ed position after being depressed. Do
not operate the nailer if the WCE trip
mechanism is not operating properly.
Personal injury may occur.
1. Disconnect the
air supply from
the nailer.
2. Remove all
nails from the
magazine (see
Loading/
Unloading).
3. Make sure the trig-
ger and work con-
tact element (WCE)
move freely up and
down without stick-
ing or binding.
! CAUTION
! WARNING
3. Insert a stick of
nails (see
"Fasteners" sec-
tion) into the
magazine. Make sure the pointed
ends of the nails are resting on the
bottom ledge of the magazine
when loading. Make sure the nails
are not dirty or damaged.
4. Push the maga-
zine cover for-
ward until the
latch catches.
5. Always unload all fasteners before
removing tool from service.
Unloading is the reverse of loading,
except always disconnect the air
supply before unloading.
ADJUSTING THE NAIL PENETRATION
The nailer is equipped with an
adjustable depth of drive feature. This
allows the user to determine how deep
a fastener will be driven into the work
surface.
1. Adjust operating pressure so nails
are driven consistently. Do not
exceed 100 psi.
2. To drive the nail shallower, turn the
wheel (C) to right to the extent
desired.
3. To sink a nail deeper, turn the
wheel (C) to left to the extent
desired.
4. Make sure trigger
and work contact
element (WCE)
move freely up and
down without binding or sticking
after each adjustment.
4. Reconnect air
supply to the
nailer.
5. Depress the Work
Contact Element
(WCE) against the
work surface with-
out pulling the
trigger. The nailer MUST NOT
OPERATE. Do not use the tool if it
operates without pulling the trig-
ger. Personal injury may result.
6. Remove the nailer
from the work sur-
face. The Work
Contact Element
(WCE) must return to
its original down position. The nail-
er MUST NOT OPERATE. Do not
use the tool if it operates while lift-
ed from the work surface. Personal
injury may result.
7. Pull the trig-
ger and
depress the
work contact
element (WCE) against the work
surface. The nailer MUST NOT
OPERATE.
8. Depress the
Work Contact
Element
(WCE) against
the work surface. Pull the trigger.
The nailer MUST OPERATE.
An improperly
functioning tool
must not be used. Do not actuate the
tool unless the tool is placed firmly
against the work piece.
LOADING/UNLOADING THE NAILER
1. Always connect the tool to the air
supply before loading fasteners.
2. Push down on
the latch. Pull
back on the
magazine
cover.
! WARNING
MXN102 Operating Instructions
4
1 2
1 2
Latch
BUILT TO LAST
movement
movement
(C)
movement