Motorola Netopia 6150285-00-02 - Manual

United States. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Par t 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful inter ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful inter ference to radio communications. However, there is no guarantee that inter ference
will not occur in a par ticular installation. If this equipment does cause harmful inter ference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to tr y to correct the inter ference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
■ Consult the dealer or an experienced radio TV technician for help.
Service requirements. In the event of equipment malfunction, all repairs should be per formed by our
Company or an authorized agent. Under FCC rules, no customer is authorized to repair this equipment.
This restriction applies regardless of whether the equipment is in or our of warranty. It is the responsibility
of users requiring ser vice to repor t the need for ser vice to our Company or to one of our authorized
agents. Ser vice can be obtained at Motorola, Inc., 1101 Marina Village Pkwy, Alameda, CA 94501.
Telephone: (510) 217-7660.
Important . This product was tested for FCC compliance under conditions that included the use of
shielded cables and connectors between system components. Changes or modifications to this product
not authorized by the manufacturer could void your authority to operate the equipment.
Canada
This Class B digital apparatus meets all requirements of the Canadian Inter ference -Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel
brouilleur du Canada.
Declaration for Canadian users
NOTICE: The Canadian Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operation, and safety requirements. The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. In
some cases, the company’s inside wiring associated with a single line individual
service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to the certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made by
the user to this equipment, or equipment malfunctions, may give the telecommuni-
cations company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution
Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the
maximum number of terminals allowed to be connected to a telephone inter face. The termination on an
inter face may consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed 5.
Part Number: 6150285-00-02
Safety and Certifications
Important Safety Instructions
POWER SUPPLY INSTALLATION
Connect the power supply cord to the power jack on the Motorola Netopia® Modem. Plug the power sup-
ply into an appropriate electrical outlet.
☛
CAUTION:
Depending on the power supply provided with the product, either the direct plug-in power
supply blades, power supply cord plug or the appliance coupler ser ves as the mains
power disconnect. It is impor tant that the direct plug-in power supply, socket-outlet or
appliance coupler be located so it is readily accessible.
CAUTION (North America Only) : For use only with a CSA Cer tified or UL Listed Limited
Power Source or Class 2 power supply, rated 12Vdc.
TELECOMMUNICATION INSTALLATION
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injur y to persons, including the following:
•
Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundr y
tub, in a wet basement or near a swimming pool.
•
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electrical shock from lightning.
•
Do not use the telephone to repor t a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
Description
Communications interfaces: The Motorola Netopia® Gateways have an RJ-11 jack for DSL line
connections or an RJ-45 jack for cable/DSL modem connections and 1 or 4–por t 10/100Base-T Ethernet
switch for your LAN connections. Some models have a USB por t that can be used to connect to your PC;
in some cases, the USB por t also ser ves as the power source. Some models contain an 802.11b/g
wireless LAN transmitter.
Power requirements
■ 12 VDC input
Environment
Operating temperature: 0° to +40° C
Storage temperature: 0° to +70° C
Relative storage humidity: 20 to 80% noncondensing