Philips Magnavox Home Threater Set MCS 990/17 - Manual (Page 20)

19
English
SOURCE SELECTION
When selecting a source by turning SOURCE SELECT, the
audio and video inputs with the corresponding name are
activated. The incoming signal is reproduced by all audio and
– if the source includes a video signal – video outputs of the
receiver. It is possible to reassign a source selection to other
than these standard inputs.
Source selected ........Connectors used
DVD...............................COAX 1 digital audio input and
DVD IN video input
PHONO..........................PHONO IN audio input
TUNER ..........................The tuner part of the receiver is used,
all inputs are switched off.
CD .................................CD IN audio input
CDR/TAPE .....................CDR/TAPE IN audio input
TV..................................TV IN audio input and
no video input
VCR ...............................VCR IN audio input and
VCR IN video input
SAT ...............................SAT IN audio input and
SAT IN video input
The 6 CHANNEL-DVD/SACD INPUT connectors can be
assigned to any of the available sources (excluding TUNER
and PHONO). The assignment can be done via the
*
SELECT INPUT option in the menu. See below for more
details.
If a source is selected with SOURCE SELECT the standard
audio input is used. To change this, the source selection must
be reassigned to another audio input.
Example: Reassigning CD from the analog CD IN audio input
to the digital COAX 2 IN audio input.
1 Choose * SELECT INPUT from the menu and press
NEXT 2.
2 Turn SOURCE SELECT to select the source which should be
reassigned (e. g. CD).
y The name of the source is displayed and the light of the
source flashes.
3 Turn X MENU NAVIGATOR to select the input connectors
which should be used (e. g. CD - COAX2).
4 Press ENTER / OK to confirm your selection.
y
STORED is displayed briefly.
5 This source selection is now using the chosen audio input
(e. g. CD uses the COAX 2 IN input connectors,
COAX 2
lights when switching to CD).
You may assign more than one source to a source selection.
This can be useful when products are connected one after the
other in a chain.
Example: A VCR is connected to the TV but only the TV is
connected to the receiver. Both SOURCE SELECT
settings, TV as well as VCR, have to use the TV
input connectors.
1 Choose * SELECT INPUT from the menu and press
NEXT 2.
2 Turn SOURCE SELECT to select the source which should be
reassigned (e. g. VCR).
y The name of the source is displayed and the light of the
source flashes.
3 Turn X MENU NAVIGATOR to select the input connectors
which should be used (e. g. VCR - TV IN).
4 Press ENTER / OK to confirm your selection.
y STORED is displayed briefly.
5 This source selection is now using the chosen audio input (e.
g. VCR uses the TV IN input connectors, VCR TV IN is
displayed briefly when switching to VCR).
The 6 CHANNEL-DVD/SACD INPUT can be used to connect a
device with a built-in multichannel decoder (e.g. Dolby Digital,
DTS, etc.) and 6-channel output connector, i. e. a high end
DVD/SACD player.
When using the 6 CHANNEL-DVD/SACD INPUT audio input,
the receiver works as a multichannel amplifier. The source
reproduces surround sound and sends it to the receiver
divided into the necessary channels. Therefore the
SURROUND ON/OFF, HALL and SURR. MODE button have no
effect since the provided signal is already multichannel.
From a source which is connected to the
6 CHANNEL-DVD/SACD INPUT audio input cannot be
recorded.
About 6 CHANNEL-DVD/SACD INPUT
Using one source selection for two or more
appliances
Reassigning a source selection
6 CHANNEL-DVD/SACD INPUT selection
SOURCE SELECT
MFX450_eng 11/26/02 3:21 AM Page 19