Melissa 646-051 - Manual (Page 11)

10 11
USING THE BLENDER
General operation
• Fit the blender jug (4) or coffee/spice mill (9), and
put the ingredients to be blended in it as described
below.
• Start the blender by turning the on/off button (8)
to position “1” or “2” and switch it off by turning it
back to position “0”.
• To use the blender in short bursts, turn the on/off
button to position “Pulse”. The blender will run at
top speed as long as you hold the button down in
that position, and will stop when you release the
button, which then automatically reverts to position
“0”.
• You should stop the blender at regular intervals to
check whether the ingredients have been sufficiently
blended/chopped.
Using the blender jug
Attach the blender jug to the blender shaft (6) with
the handle facing away from you and to the left, and
turn it clockwise until it locks into place.
1. Attach the blender jug to the blender shaft (6) with
the handle facing away from you and to the left, and
turn I clockwise until it locks into place.
2. Place the food in the blender jug.
. Fit the jug lid () by placing it over the blender with
the pin to the right of the handle and turning the lid
clockwise until it locks into place.
4. Fit the filler cap (2) by inserting it into the hole in the
lid so the pins on the cap fit into the grooves in the
lid. Turn the cap clockwise until it locks into place.
5. Start the blender.
6. Use the filler cap to add more ingredients during
blending, if necessary. In that case, stop the blender
before removing the cap to avoid splashes.
7. Remove the filler cap, the jug lid and the blender jug
in reverse order. Hold the release button (1) down
while twisting off the lid.
Important! If the blender is to be used to chop different
types of food (e.g. raw meat followed by vegetables,
or egg followed by fruit), you must wash the parts that
come into contact with food between each type of food.
Using the coffee/spice mill
The coffee/spice mill is ideal for grinding coffee
beans and various spices.
1. Attach the mill to the blender shaft and turn it
anticlockwise until it locks into place.
2. Place the items to be ground in the mill.
. Fit the mill lid (10) by placing it on the mill and
turning it anticlockwise until it locks into place.
4. Start the blender.
5. Remove the mill lid and the mill in reverse order.
Storage
Ensure that the blender is clean and dry before storing.
CLEANING
• Before cleaning, remove the plug from the wall
socket.
• The best way to clean the base of the blender is to
wipe it with a well-wrung cloth using hot water and
a little detergent. The base must not be submerged
in any form of liquid!
• The blender jug, the coffee/spice mill, the two lids
and the filler cap can be washed in the usual way.
• Do not use any kind of strong or abrasive cleaning
agent on the blender parts. Never use a scouring
sponge or similar to clean the blender, as the
surface may be damaged.
INFORMATION ON DISPOSAL AND RECYCLING OF
THIS PRODUCT
Please note that this Adexi product is marked with
this symbol:
This means that this product must not be disposed of
together with ordinary household waste, as electrical
and electronic waste must be disposed of separately.
In accordance with the WEEE directive, every member
state must ensure correct collection, recovery, handling
and recycling of electrical and electronic waste. Private
households in the EU can take used equipment to
special recycling stations free of charge. In certain
member states, used appliances can be returned to the
dealer where they were bought on the condition you
buy new products. Contact your retailer, distributor or
the municipal authorities for further information on what
you should do with electrical and electronic waste.
GUARANTEE TERMS
The guarantee does not apply:
• if the above instructions are not followed
• if the appliance has been interfered with
• if the appliance has been mishandled, subjected to
rough treatment, or has suffered any other form of
damage
• if faults have arisen as a result of faults in your
electricity supply.
Due to the constant development of our products in
terms of function and design, we reserve the right to
make changes to the product without prior warning.
IMPORTER
Adexi Group
We cannot be held responsible for any printing errors.