Philips Magnavox cmwR20v6 - Manual (Page 79)

79
Recording
Playing
discs
Editing
Getting
started
Changing
the
Setup
menu
VCR
functions
Others
Before
you
start
Connections
EN
xxxx
Others
Troubleshooting (cont’d)
Error message Cause Solution
Disc Error
--- Please eject the disc. ---
Playback feature may not be
available on this Disc.
• Unplayable disc is inserted in the
unit.
• The disc is upside down.
• Insert the standardized disc which
bear the marks on page 41.
• Insert the disc with the labeled side
facing up.
Region Error
--- Please eject the disc. ---
Playback is not authorized in
your region.
• The region of the DVD-Video disc
does not match the ones on the
unit.
• Insert the DVD-Video disc with
region codes 1 or ALL.
Parental Lock On
The current selected parental
level prohibits playback.
• The current selected parental
level in the Setup menu prohibits
playback.
• Check the “Parental Lock” setting
(pages 72-73).
Recording Error
This program is not allowed to
be recorded.
• The recording function encountered
the copy prohibited program.
• You cannot record copy prohibited
programs.
Recording Error
This program is not recordable
in +VR mode.
• You are trying to record the copy-
once program.
• You cannot record the copy-once
program.
Recording Error
Can not record on this disc.
• You are trying to record onto the
disc which is unrecordable, or the
disc status is unable to record.
• The disc is dirty.
• The disc is damaged.
• Insert the recordable disc, and ensure
the disc status satisfies the recording
requirements (pages 25-26).
• Clean the disc with a cleaning cloth.
• Replace the disc.
Recording Error
This disc is protected and not
recordable.
• You are trying to record on to the
protected disc which is set in the
Disc Edit menu.
• Release the disc protect setting in
the Disc Edit menu (pages 36, 64).
Recording Error
Disc is full.
(No area for new recording)
• You are trying to record onto
the disc which has no space for
recording.
• Insert the recordable disc with
enough recording space.
Symptom Remedy
D
V
D
“Repairing” appears on the TV screen. • If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after “Repairing” disappears), a
Repairing process will begin automatically just after turning the unit
on again.
It may take several minutes up to about four hours.
• If you intend to cancel the Repairing process, press
[OPEN/CLOSE A] on the front panel, then select “Yes” with
[{ / B] and press [OK]. After that, the disc tray will automatically
open. In case the Repairing process is canceled, the disc MAY
NOT work.
Repairing
In a case you intend to cancel the
Repairing process.
Repairing
Do you want to cancel a repairing process ?
When selecting “Yes”, the disc may not be
usable.
Yes No
V
C
R
Picture noise appears. • Head cleaning for VCR may be necessary. Refer to “AUTO HEAD
CLEANING”.
• Adjust tracking control for better picture by pressing
[CHANNEL L / K] on the front panel or [CHANNEL
-
/
+
] on the
remote control while you are playing a videotape.
The tape does not play. • No videotape is inserted.
Recording does not start immediately
after you press [VCR REC I].
• Make sure the videotape has a record tab when you record to a
videotape. If needed, cover the hole with cellophane tape.
The remote control does not
function.
• Check if a videotape is in this unit.
The motor rotates even when
playback/recording is stopped. • The motor may rotate for the duration of approximately 5 minutes
for efficient operation. This is not a malfunction.