Marantz PMD570 - Manual (Page 21)

Back
1. BALANCED IN
ANALOG XLR inputs, L & R
BALANCED IN R L
R E F = + 1 6 d B u / 0 d B F S
+ 24 + 24
GROUND
HOT (+) COLD (-)
2 1 3 L
R
IN OUT
ANALOG DIGITAL
IN
OUT
(SPDIF)
I / O RS 232C REMOTE2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
C A U T I O N
UL C US LISTED
AUDIO SYSTEM 69 FM
S E R I A L N O .
WARNING: SHOCK HAZARD- DO NOT OPEN.
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
A C I N
MODEL NO. PMD570
AC120V 60HZ 0.5A
MADE IN JAPAN
REMOTE1
1 2
XLR connectors are available for balanced analog
input.
The balanced XLR connection permits trimming,
adjusting the input level. See TRIM L & R below.
For mono recording use either jack. Input from both
jacks is mixed internally during mono recording.
Mono recording will appear on the left level meter.
To record an incoming signal from the XLR jacks,
Bal.In must be selected in the Input Menu.
BALANCED IN R L
REF=+16dBu/0dBFS
+ 24 + 24
Example display
at stop.
- 21 -
2. ANALOG IN / OUT jacks
RCA jacks for line level input
and output.
L & R ANALOG IN jacks
Plug L and R RCA jacks in here
to connect to the Line level
L
R
IN OUT
ANALOG
To select BALANCED IN XLR jacks as inputs for
recording:
1. Push and release the MENU/STORE button.
2. Choose a Preset by turning the Jog Wheel.
3. Select the Preset by pushing and releasing the Jog
Wheel.
4. Turn the Jog Wheel so Input is flashing.
5. Push and release the Jog Wheel so the input
choice is flashing.
6. Turn the Jog Wheel so Bal.In is flashing.
7. Push and release the Jog Wheel to accept the
Bal.In choice.
8. Push and release the MENU/STORE button to
store the Menu change. Stored is displayed.
See page 24 for a full presentation of Menu
selection.
output jacks of an external mixer or other audio
playback device.
For mono recording use either jack.
To record, UnBal. must be selected in the Input Menu.
TIME
REC REMAIN L
R
-dB over 0 2 6 12 20 40 00
-dB
LINE
GROUND
HOT (+) COLD (-)
2 1
3
REF=+16dBu/0dBFS
+ 24 + 24
BALANCED IN R L
Trim L & R
You can use a small screwdriver to adjust the Trim of
the XLR L & R inputs.
The Trim is factory preset at +16 dBu with an adjust-
ment range from 0 to +24 dBu.
Some professionals prefer to first set the Trim using a
meter and to do a fine adjustment by listening for
distortion and watching the level meters on the
PMD570.
The pin out for the XLR jacks is printed on the
PMD570 for easy reference:
Pin 1 ground,
Pin 2 HOT +,
Pin 3 COLD -
.
Example display
at stop.
To select ANALOG IN RCA jacks as inputs for
recording:
1. Push and release the MENU/STORE button.
2. Choose a Preset by turning the Jog Wheel.
3. Select the Preset by pushing and releasing the Jog
Wheel.
4. Turn the Jog Wheel so Input is flashing.
5. Push and release the Jog Wheel so the input
TIME
REC REMAIN L
R
-dB over 0 2 6 12 20 40 00
-dB
LINE
pin
out