Wiring with the rca jack inputs, Figure 4 - using the rca jack inputs, Page 8 powered subwoofers – MK Sound MX-125 MK II User Manual

Page 8: Preamp, Amplifier or receiver

Advertising
background image

page 8

powered subwoofers

In the MX-300, MX-200, and MX-125 Mk II, a full-range signal (including deep bass) is fed to your

Satellites. To roll off (filter) the signal fed to the Satellite speakers for biamplification, you must:

1.

Have a separate amp and preamp OR a receiver or integrated amp that allows you to
separate its amp and preamp stages.

2.

Use a surround sound processor or receiver that has built-in high-pass filters and a subwoofer
output jack.

3.

Add an M&K Electronic High-Pass Filter to your system. See Page 9 for more information.

WIRING WITH THE RCA JACK INPUTS

The "INPUT" RCA jacks on the Subwoofer allow you to directly connect the Subwoofer to preamp-

level components such as surround sound processors, preamplifiers, integrated amps and receivers
with preamp outputs, Electronic High-Pass filters, crossovers, etc.

Using these inputs gives you better bass quality than using the speaker inputs (it bypasses your

amp or receiver's amplifier stage). If you don't have a subwoofer output available, you must have
preamp outputs on your preamp, amp, or processor. If you have only one set of preamp outputs, use
a Y-connector to feed both the amplifier and the Subwoofer. In many cases, using a Y-connector may
slightly degrade the Satellite speakers' sound quality. Please feel free to experiment.

To connect the Subwoofer in this way, simply run a set of shielded RCA - RCA interconnect cables

from the output jacks on your component to the "FROM PREAMP" jacks on the Subwoofer's backplate.
See Figure 4.

FIGURE 4 - USING THE RCA JACK INPUTS

If you have one Preamp Output, connect both the Subwoofer and the Amplifier to it.

100

PHASE

10391 Jefferson Blvd, Culver City, CA 90232 310/204-2854

MILLER & KREISEL SOUND CORPORATION

RIGHT

RIGHT

FROM PREAMP

BASS LEVEL

LOW PASS FILTER

(Hz)

FROM AMPLI

FIER

MAX

50

75

60

125

Made in U.S.A.

T

4 AMP

120 VAC 50/60 Hz

TO SPEAKERS

LEFT

RIGHT

LE

FT

MIN

LEFT/MONO

SLOW-BLOW

ATTENTION:

DEBRANCHER AVANT DE

REMPLACER LE FUSIBLE.

UTILIZER UN FUSIBLE

DE RECHANGE DE MEME TYPE.

CAUTION:

DISCONNECT SUPPLY CORD

BEFORE CHANGING FUSE.

REPLACE FUSE ONLY

WITH SAME TYPE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS:

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.

+

–

RIGHT

LEFT

PREAMP

MADE IN USA

INPUT

4 ohms

MIDRANGE CONTOUR

MID

EFFICIENCY

NORMAL

SATELLITE SPEAKER

TREBLE CONTOUR

MID

TWEETER

NORMAL

LOW

TWEETER

LOW

EFFICIENCY

MILLER & KREISEL
SOUND CORPORATION

10391 Jefferson Boulevard., Culver City, CA 90232
Voice (310) 204-2854 Fax (310) 202-8782

INPUT

4 ohms

MIDRANGE CONTOUR

MID

EFFICIENCY

NORMAL

SATELLITE SPEAKER

TREBLE CONTOUR

MID

TWEETER

NORMAL

LOW

TWEETER

LOW

EFFICIENCY

MILLER & KREISEL
SOUND CORPORATION

10391 Jefferson Boulevard., Culver City, CA 90232
Voice (310) 204-2854 Fax (310) 202-8782

MADE IN USA

AMPLIFIER

OR RECEIVER

L

R

LEFT

RIGHT

RIGHT

LEFT

MAIN INPUT

RIGHT

LEFT

MAIN OUT 1

MAIN OUT 2

Advertising
This manual is related to the following products: