Philips Magnavox MPDR-3328CPE - Manual (Page 4)

4 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Electronic Appliances -
To light electronic appliances refer to the de-
tailed lighting instructions found in both En-
glish and French on
pages 14 and 15 of these
instructions respectively. Electronic appliance
lighting instructions may also be found on
the pull out lighting instruction labels at-
tached to the gas control valve.
Honeywell Electronic Gas Valve
2. When lit for the first time, this appliance will
emit a slight odor for an hour or two. This is
due to the “burn-in” of internal paints and
lubricants used in the manufacturing process.
3. Keep lower control compartment clean by
vacuuming or brushing at least twice a year.
More frequent cleaning may be required due to
excessive lint from carpeting, bedding materi-
als, etc. It is important that control compart-
ments, burners and circulating air passage-
ways of the appliance be kept clean and clear of
obstructions of venting and combustion air.
4. Always turn off gas to the pilot (millivolt
appliances) before cleaning. Before re-light-
ing, refer to the lighting instructions in this
manual. Instructions are also found on a pull-
out panel located on the floor of the appliance.
5. Always keep the appliance area clear and
free from combustible materials, gasoline and
other flammable liquids.
6. Remember, Millivolt appliances have a con-
tinuous burning pilot flame. Exercise caution
when using products with combustible vapors.
Honeywell Millivolt Gas Valve Figure 4
Figure 3
HI
L O W
TPTH
TP
TH
PILO
T
PIL
O
T
ON
it
OFF
Variable Flame Height Adjustment
Manifold Pressure Port
Inlet Pressure Port
Main Gas
Control Knob
Piezo Ignitor
IN OUT
Piezo Ignitor
Optional Burner ON/OFF
Rocker Switch Location
Factory-Installed Blower ON/OFF
Rocker Switch Location
Main Gas
Control Knob Variable Flame
Height Adjustment
Piezo Ignitor
O
N
OFF
P
I L OT
L O
H I
Manifold
Pressure Port Inlet
Pressure Port
Optional ON/OFF Rocker Switch
Location (One of Two Places)
Piezo Ignitor
Optional Burner ON/OFF
Rocker Switch Location
SIT Millivolt Gas Valve
ON/OFF Switch
Electronic
Gas Control
Valve
Inlet
Pressure
Port
Manifold Pressure Port
OFF
IN
PSI
ON
CONTROL
IG
N
IT
E
R
Figure 2
If your electronic appliance is equipped with
an optional remote wall switch or remote con-
trol kit the appliance main burner may be
turned on and off with the wall switch or
remote control.
If your electronic appliance is not equipped
with a wall switch or remote control, the main
burner must be turned off and on with the gas
control switch. Toggle the switch from ON to
OFF to operate the main burner .
Variable Flame Height Adjustment
( Millivolt Appliances only)
1. All Millivolt appliances are equipped with a
variable gas control valve. Flame height for
these models may be adjusted through a range
between fixed low and high settings, alter-
nately, while the appliance is in operation.
Adjust the flame height as desired after lighting
the appliance by rotating the variable adjust-
ment control knob located on the front of the
valve
(refer to Figure 3 - SIT, 4 - Honeywell).
Piezo Ignitor
Drop Down
Control
Compartment
Access Panel
SIT Gas Valve
Honeywell
Gas Valve
Figure 1
Sit and Honeywell Millivolt Gas Valve
Showing Piezo Ignitor Location (Each Unit is
Equipped with Only One of these Gas Valves)
See Figure 2 (SIT), 3 (Honeywell) for the
location of the piezo ignitor.
Millivolt appliances may be fitted with an optional
burner ON/OFF Rocker Switch. The optional ON/
OFF Rocker switch will be installed in the bracket
just beneath the gas control valve. Once the pilot
is lit, the ON/OFF rocker switch will control the
appliance ON/OFF operation. To operate: Toggle
the switch between its ON and OFF positions.
If your millivolt appliance is equipped with an
optional remote wall switch or remote control
kit and the pilot is lit, the appliance main burner
may be turned on and off with the wall switch or
remote control.