Operational setup, Connectors, Mechanical specifications – Marshall electronic V-R102DP-HD User Manual
Page 2: Switch settings, adjustments and indicators, V-r102p-hd, Dry erase, Tally lamps, V-r82dp-hd users guide marshall electronics, V-r102dp-hd users guide marshall electronics, Vga/xga connector
6
Operational Setup
1. Unpack the V-R102DP-HD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have
occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.
If you are not located within the continental United States call +1 310-333-0606.
2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when
installed to prevent possible damage to the V-R102DP-HD internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R102DP-HD for all outputs
to be activated. All BNC connectors should be rated for 75Ω.
4. Plug the V-PS12-5V-1 power supply into the A.C. source
5. Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.
6. Turn on each of the V-R102DP-HD screens by depressing the power switch located on the front of the unit for each screen.
7
Connectors
* HDSDI/SDI Inputs comply to SMPTE-259M, 292M, SDI-270Mbs , HDSDI-1.485 Gb/s
* Component Inputs comply to SMPTE274M, 294M,295M,296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
S-Video In
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yin
Pin4 - Cin
S-Video Out
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout
12 VDC from
V-PS12-5V-1 power supply
Left Pin - Pos
Right Pin- Neg
Active Outputs require power to be applied
All input signals appear as output signal
Analog output signals are buffered and amplifi ed
VGA/XGA Connector
PIN# SIGNAL
PIN# SIGNAL
1 RED
9 NC
2 GREEN
10
NC
3 BLUE
11
NC
4 NC
12
NC
5 GND
13
HSYNC
6 RED
SHIELD
14
VSYNC
7 GREEN
SHIELD
15
NC
8 BLUE
SHIELD
DVI-I Connector
Pin#
Signal
Pin#
Signal
1
T.M.D.S DATA 2-
16
HOT PLUG DETECT
2
T.M.D.S DATA 2+
17
T.M.D.S DATA 0-
3 T.M.D.S
DATA
2/4
SHIELD
18 T.M.D.S
DATA
0+
4
T.M.D.S DATA 4-
19
T.M.D.S DATA 0/5
SHIELD
5
T.M.D.S DATA 4+
20
T.M.D.S DATA 5-
6
DDC CLOCK
21
T.M.D.S DATA 5+
7
DDC DATA
22
T.M.D.S CLOCK
SHIELD
8
ANALOG VERT. SYNC
23
T.M.D.S CLOCK+
9
T.M.D.S DATA 1-
24
T.M.D.S CLOCK-
10 T.M.D.S
DATA
1+
11 T.M.D.S
DATA
1/3
SHIELD
C1 ANALOG
RED
12 T.M.D.S
DATA
3- C2 ANALOG
GREEN
13 T.M.D.S
DATA
3+ C3 ANALOG
BLUE
14
+5V POWER
C4
ANALOG HORZ SYNC
15 GND
C5 ANALOG
GROUND
Dimensions
19.12” w x 8.67” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)
V-R82DP-HD Weight
5.5 lbs (2.4 kg)
V-PS12-5V-1 Power Supply Weight
1 lbs (0.45kg)
5
Mechanical Specifications
3
6
V-R82DP-HD Users Guide
Marshall Electronics
Pin1-M2Yel
Pin2-M2Red
Pin3-M2Grn
Pin4-
Pin5-Gnd
Pin6-
Pin7-
Pin9-
Pin10-
Pin11-M1Yel
Pin12-M2Red
Pin13-M3Grn
Pin14-
Pin15-Gnd
Tally IN
DB-15 Female
Dry Erase
Image Adjustment Controls
Note: Tint only functions when NTSC
Video or S-Video are selected
Screen aspect ratio switch 4:3 or 16:9 selector and indicators
4:3 Aspect 16:9 Aspect
8
Switch Settings, Adjustments and Indicators
Tally Lamps
V-R102DP-HD Users Guide
Marshall Electronics
V-R102P-HD