Multiquip Cutter 1 Concrete/Asphalt Saw CD605E16 (5 HP Electric Motor) - Manual (Page 9)

STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #6 (06/06/08) — PAGE 9
STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION
Diamond Blade Safety
■ Use appropriate steel centered diamond blades
manufactured for use on concrete saws.
■ ALWAYS inspect diamond blades
before each use. The blade should
exhibit no cracks, dings, or flaws in
the steel centered core and/or rim.
Center (arbor) hole must be
undamaged and true.
■ Examine blade flanges for damage, excessive wear and
cleanliness before mounting blade. Blade should fit snugly
on the shaft and against the inside/outside blade flanges.
■ Ensure the blade is marked with an operating speed greater
than the blade shaft speed of the saw.
■ Only cut the material that is specified by the diamond blade.
Read the specifications of the diamond blade to ensure the
proper tool has been matched to the material being cut.
■ ALWAYS keep blade guards in place. Exposure of the
diamond blade must not exceed 180 degrees.
■ Ensure that the diamond blade does not come into contact
with the ground or surface during transportation. DO NOT
drop the diamond blade on ground or surface.
■ The engine governor is designed to permit maximum engine
speed in a no-load condition. Speeds that exceed this limit
may cause the diamond blade to exceed the maximum safe
allowable speed.
■ Ensure that the blade is mounted for proper operating
direction.
General Safety
■ ALWAYS read, understand, and follow procedures in
Operator's Manual before attempting to operate equipment.
■ ALWAYS be sure the operator is familiar with proper safety
precautions and operating techniques before using the saw.
■ NEVER leave the machine
unattended while running.
■ Block the unit when leaving or when using on a slope.
■ ALWAYS check to make sure that the operating area is clear
before starting the engine.
■ Maintain this equipment in a safe operating condition at all
times.
■ ALWAYS stop the engine before servicing, adding fuel and
oil.
■ NEVER run the engine without the air filter. Severe engine
damage could occur.
■ ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
■ AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts, this can cause a serious
injury.
■ ALWAYS keep clear of
rotating or moving parts while the
saw is in operation.
■ ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of
the reach of children.
■ NEVER use accessories or attachments which are not
recommended by the manufacturer for this equipment.
Damage to the equipment and/or injury to user may result.
WARNING
■ ALWAYS check to make sure that the
operating area is clear before starting the
engine.
■ Keep all inexperienced and unauthorized people away from
the equipment at all times.
WARNING
Electric Saws
■ ALWAYS connect electric motor of the saw to a power source
in compliance with all local and state electrical codes. This
must be performed by a qualified electrician. After this
connection is made, it will be necessary to check the rotation
of the motor shaft. The shaft rotation should be
counter-
clockwise when viewing the motor from the shaft extension
end. If the rotation of the shaft is incorrect make necessary
changes for the correct shaft rotation.
■ MAKE CERTAIN the power cord/extension cord is free from
damage and that the grounding circuit is operational.
■ MAKE CERTAIN the extension cord that you are using is
intended to be used in the environment you are using it in. If
an extension is used, NEVER submerge the connection in
water. To reduce the risk of electric shock, always make water-
tight connections.
■ MAKE CERTAIN the "ON/OFF" switch is in the "OFF" position
before plugging in the power cord/extension cord to avoid
accidental starting.
■ Use only the gauge wire and length of cord recommended for
the motor size. Refer to Table 3 in this manual.
■ When cutting, ALWAYS be aware of the location of the cord.
■ NEVER use a worn, frayed or damaged extension cord.