Insignia NS-HTIB51A - Manual (Page 24)

20
Insignia NS-HTIB51A 5.1 Channel Home Theater System
www.insigniaproducts.com
COAX, OPT1, OPT2–Select the digital audio input
to which the video component has been
connected.
- - - - -–Select if you are using an analog audio input.
Configuring speakers (Sp Config menu)
This section explains how to specify which speakers
are connected and defines their sizes.
For speakers with a cone diameter larger than 6.5
inches (16 cm), specify Large (full band). For those
with a smaller diameter, specify Small (default
crossover 120Hz).
The crossover frequency can be changed in the
Crossover submenu.
Setting the crossover frequency (Crossover Frequency
submenu of Sp Config menu)
This setting is recommended for the speakers that
you specify as Small. To get the best bass
performance from your speaker system, you need
to set the crossover frequency according to the size
and frequency response of your speakers. Options
include 40Hz, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz,
150Hz, and 200Hz.
Use the diameter of the smallest speaker in your
system when choosing the crossover frequency.
Using the Double Bass setting (Double Bass submenu of
Sp Config menu)
Lets you boost bass output by feeding bass sounds
from the front left, right, and center channels to the
subwoofer. Optional settings are On and Off.
Setting speaker distance (Sp Distance menu)
Lets you specify the distance from each speaker to
the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
Notes
• When an HDMI IN is assigned to an input
selector as explained here, the digital audio
input for that input selector is automatically set
to the same HDMI IN. In addition to the usual
inputs, such as COAX, you can also select HDMI
inputs.
• The available sampling rate for PCM signals
from a digital input (optical and coaxial) is
32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
• If you connect a component to a UNIVERSAL
PORT jack, you cannot assign any input to the
PORT selector.
Note
Some of the settings in this section are made
automatically by the Audyssey 2EQ® Room
Correction and setup function. See “Using the
Audyssey 2EQ® room correction and speaker setup”
on page 12.
Note
Speaker Configuration, Crossover Frequency, and
Double Bass settings are disabled while headphones
are connected, or when Audio TV OUT is set to On.
Speaker(s) Configuration
Subwoofer
Yes–if a subwoofer is connected.
No–if no subwoofer is connected.
Front
Small–If speaker cone is 6.5 inches (16 cm) or less in
diameter.
Large–If speaker cone is larger than 6.5 inches (16 cm)
in diameter.
Note: If the Subwoofer setting is No, the default setting
for this is Large and cannot be changed.
Center and Surround
Small–If speaker cone is 6.5 inches (16 cm) or less in
diameter.
Large–If speaker cone is larger than 6.5 inches (16 cm)
in diameter.
None–If no center speaker is connected.
Note: If the Front setting is Small, the Large option
cannot be selected. When Speakers B is On, these
speakers output no sound.
Speaker cone diameter
Recommended
Crossover Frequency
Over 8 in. (20 cm) 40/50/60 Hz
6-1/2 to 8 in. (16 to 20 cm) 80 Hz
5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz
3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz
Under 3-1/2 in. (9 cm) 150/200 Hz
Notes
• For a more accurate setting, look up your
speaker’s specifications.
• Choose a higher crossover frequency if you
want more sound from your subwoofer.
Note
This function can only be set if the Subwoofer
setting is Yes, and the Front setting is Large. This
setting is not made by Audyssey 2EQ®.
Note
This setting is made automatically by the Audyssey
2EQ® Room Correction and setup function. See
“Using the Audyssey 2EQ® room correction and
speaker setup” on page 12.
Option Configuration
Unit
Feet (default)–Distances can be set from 1 to 30
feet, in one foot increments.
Meters–Distances can be set from 0.3 to 9.0 meters,
in 0.3 meter increments.
Left, Center, Right,
Surround Right, Surround
Left, Subwoofer Specify the distance from each speaker to your
listening position.
Notes
• The speaker distance setting is disabled while
headphones are connected, or when Audio TV
OUT is set to On.
• Speakers that you set to No or None in the
speaker configuration (Sp Config menu) cannot
be selected.
• The Center, Right, and Subwoofer distances can
be set up to 5 ft. (1.5 m) more or less than the
Left distance. For example, if the Left distance is
set to 20 ft. (6 m), the Center, Right, and
Subwoofer distances can be set between 15 and
25 ft. (4.5 and 7.5 m).
• The Surround distances can be set up to 5 ft.
(1.5 m) more or 15 ft. (4.5 m) less than the Left
distance. For example, if the Left distance is set
to 20 ft. (6 m), the SurrRight and SurrLeft
distances can be set between 5 and 25 ft. (1.5
and 7.5 m).
NS-HTIB51A_10-0114_MAN_.book Page 20 Tuesday, April 13, 2010 10:19 AM