InFocus C 5YC - Manual (Page 6)

English
5
SPECIFICATIONS
Voltage (by areas)* (110 V, 230 V, 240 V)
Cutting Depth 35 mm Max.
Power Input* 1010 W
Capacity 125 mm Max. Hole diam. 20 mm
Dimensions (Length × Height × Width) 284 mm × 208 mm × 320 mm
No Load Speed 9600 / min
Weight (without cord) 2.9 Kg
STANDARD ACCESSORIES
(1) Box wrench ............................................................... 1
(2) Guide .......................................................................... 1
(3) Dust bag .................................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
⅜ Carbide Tipped Saw Blade (Dia. 125 mm) for the
gypsum board.
Optional accessories are subject to change without
notice.
APPLICATIONS
(1) Cutting the hard boards types T9 and T7.
(ex. harditex, hardiflex, etc.)
(2) Cutting the gypsum board.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
* Be sure to check the nameplate on product as it is subject to change by areas.
PRECAUTIONS ON USING CIRCULAR SAW
1. Do not use saw blades which are deformed or
cracked.
2. Do not use saw blades made of high speed steel.
3. Do not use saw blades which do not comply with
the characteristics specified in these instructions.
4. Do not stop the saw blades by lateral pressure on
the side surface of disc.
5. Always keep the saw blade sharp.
6. Ensure that the lower guard moves smoothly and
freely.
7. Never use the circular saw with its lower guard
fixed in the open position.
8. Ensure that the retraction mechanism of the guard
system operates accurately.
9. Never operate the circular saw with grasping the
saw blade upside down or to the lateral direction.
10. Ensure that the material is free of foreign matters
such as nails.
11. For model C5YC, the saw blade’s diameters which
can be mounted are 125 mm or less.
12. Be careful of brake kickback.
This circular saw incorporates an electric brake that
functions when the switch is released. As there is
some kickback when the brake functions, be sure to
hold the main body securely.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Prepare a wooden workbench (Fig. 1)
Since the saw blade will extend beyond the lower
surface of the lumber, place the lumber on the
workbench prior to cutting. If a square block is
utilized as the workbench, adjust leveling to ensure
that it is properly stabilized. An unstable workbench
will result in hazardous operation.
CAUTION
● To avoid possible accident, remains always ensure
that the portion of workpiece after cutting is securely
anchored or held in position.
ADJUSTING THE SAW PRIOR TO USE
1. Adjusting the cutting depth (Fig. 2)
CAUTION
If the clamp lever is loose, injury can result.
Tighten it securely after adjustment.
(1) To adjust cutting depth, loosen the clamp lever and,
while holding the base with one hand, move the
main body up and down to obtain the prescribed
cutting depth. After adjusting to the prescribed
cutting depth, tighten the clamp lever securely.
(2) When a base and saw blade are right-angled, it cuts
deeply using the scale of a link part, and the depth
can be adjusted (Fig. 3).
01Eng_C5YC_ChT.P65E 10/18/06, 11:58 AM 5