Ingersoll-Rand 650556-1 - Manual (Page 2)

PAGE 2 OF 4 650556-1
PARTS LIST / 650556-1
ITEM DESCRIPTION (Size in Inches) QTY PART NO. ITEM DESCRIPTION (Size In Inches) QTY PART NO.
1 Two Ball Piston Pump (1) 650685-P43
2 Cart Assembly (Includes Items 6 thru 14) (1) 67139
6 Washer (3/8”) (4) Y13-6-C
7 Screw (3/8” - 16 x 1-1/4”) (4) Y6-66-C
8 Nut (3/8” - 16) (4) Y12-6-C
10 Brace (1) 95102
11 Screw (5/16” - 18 x 3/4”) (4) Y6-53-C
12 Nut (5/16” - 18) (4) Y12-5-C
13 Washer (5/16”) (4) Y14-516-C
14 Cart Welding Assembly (1) 67138
15 Material Filter (Includes Item 16) (1) 651422-70
16 Plug (3/8”) (1) Y17-13-S
17 Muffler (1) 91790-ZZ
j 18 3/4” Suction Hose Assembly (1) 622606-5
j 19 90_ Elbow
(3/4”) (1) Y43-15-S
j 20 Suction Tube (5 Gallon) (1) 94263-1
21 Hose Assembly (1) 628092-F
22 Gauge (1) 104500
23 Piggyback Filter/Regulator (1) P39344-100
24 Nipple (1/2” x 2” (m)) (1) Y44-31-C
25 Bushing (1/2” - 14 (m) x 1/4” - 18 (f)) (1) 94271
26 Nipple (1/4” - 18 (m)) (2) 1950
27 Street Tee (1/4” - 18) (1) 94270
28 Needle Valve (1) 94269
29 Adapter (1” (m) x 1/2” (f)) (1) 94256
30 90 _ Adapter
(1” (m) x 1/4” (f) x 3/4” (f)) (1) 94254
31 Plug (1) Y17-11-S
j Parts included in 67140-1 Asm (std)
Available: 67140-2 Asm. uses 94263-2 (36” Inlet Tube)
OPERATING INSTRUCTIONS
WARNING DO NOT EXCEED MAXIMUM OPERATING PRES-
SURE OF 6000 P.S.I. (414 BAR) AT 100 P.S.I. (6.9 BAR) AIR IN-
LET PRESSURE.
WARNING REFER TO THE PUMP MANUAL FOR ADDITION-
AL OPERATING AND SAFETY PRECAUTIONS AND OTHER IM-
PORTANT INFORMATION.
INSTALLATION
OPERATING INSTRUCTIONS / INITIAL SETUP PROCEDURE
This unit comes assembled except for the air supply hose, gun and ma-
terial hose which must be attached.
x A connector, coupler and air supply hose and must be supplied to
the air regulator.
x Attach a Ground wire to a suitable ground and the Ground Lug
provided on the pump Air Motor.
x Keep containers covered to prevent contamination.
1. Turn the knob on the air regulator counter-clockwise to zero p.s.i.
2. Attach hose and gun. Place pump inlet tube into a full container of
material.
3. Start the pump to cycle by turning the air regulator knob clockwise.
The pump will cycle several strokes until pressure is built up in the
system, at which time it will stall, check for any loose fittings or leak-
age. Check all connections and re-tighten as necessary.
4. Relief Valve (28) is used to relieve pressure in the hose in order to
change spray tips. Open the relief valve to relieve pressure. Close
the relief valve to continue spray operation.