Intel D845GLLY - Manual (Page 4)

Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability
whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to
fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not
intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time,
without notice.
All products, dates and figures specified are preliminary based on current expectations, provided for planning purposes only, and are subject to change
without notice. Availability in different channels may vary.
The Intel ® Desktop Boards D845GLLY and D845GLAD may contain design defects or errors known as errata, which may cause the product to deviate
from published specifications. Current characterized errata are available on request.
Intel, Pentium, Celeron, Intel NetBurst, and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United
States and other countries.
* Other names and brands may be claimed as the property of others.
** Intel ® Desktop Board D845GLAD supports DDR SDRAM memory and Intel ® Desktop Board D845GLLY supports PC133 SDRAM memory.
Currently validated to 1.0GB using 256Mb technology. For latest validated memory support, visit
http://developer.intel.com/support/motherboards/desktop/
*** Not supported on all operating systems. See product guide for details.
Copyright © 2002 Intel Corporation. 0302/MS/CW
Intel ® Desktop Boards D845GLAD and D845GLLY Technical Specifications
Processor
Processors Supported Intel ® Pentium ® 4 and Celeron ® processors with
(via mPGA478-pin socket) Intel ® NetBurst ™ microarchitecture including a
400-MHz system bus in the mPGA478-pin package
and supporting frequencies starting at 1.40 GHz
Intel ® 845GL Chipset Intel ® 845GL Graphics Memory Controller Hub
(GMCH) with Accelerated Hub Architecture bus
Intel ® 82801DB I/O Controller Hub (ICH4) with
Accelerated Hub Architecture bus
Intel ® 82802AB Firmware Hub (FWH)
Graphics Memory Designed to support up to 2GB** (w/512Mb
Controller Hub (GMCH) technology) of either DDR266/200 SDRAM memory
(Desktop Board D845GLAD) or PC133 SDRAM
(Desktop Board D845GLLY)
ICH4 I/O Controller Hub Ultra ATA/66/100
Ultra DMA/33
Allows support of four PCI bus masters
I/O Features Integrated super I/O LPC bus controller
Four PCI local bus slots
Power management support for ACPI 1.0
PC 2001 compliance
USB 2.0*** • Two back panel ports (one dual stack)
• Two front panel ports (header requiring cable
to front panel)
Firmware Hub
System BIOS 4-Mb Flash EEPROM with Intel/AMI* BIOS featuring
plug-and-play, IDE drive auto-configure
Advanced configuration and power interface
V1.0b, DMI 2.0, multilingual support
Intel ® Rapid BIOS Boot Optimized POST for faster access to PC from
power-on
Audio Solution Sigmatel* STAC9750 AC’97 compliant integrated
audio solution
System Memory
Memory Capacity Two 184-pin DIMM connectors supporting up to
two double-sided DIMMS (Desktop Board
D845GLAD)
Two 168-pin SDRAM connectors supporting up
to two double sided DIMMS (Desktop Board
D845GLLY)
Memory Type DDR266 SDRAM or DDR200 SDRAM (Desktop
Board D845GLAD)
PC133 SDRAM (Desktop Board D845GLLY)
Memory Voltage 2.5V DDR memory (Desktop Board D845GLAD)
3.3V SDRAM memory (Desktop Board D845GLLY)
Wake-Up From Network
Wired for Management (WfM) 2.0 compatible.
Support for system wake up using an add-in
network interface card with remote wake-up
capability or PCI
Expansion Capabilities
Four PCI bus add-in card connectors
Jumpers and Front Panel Connectors
Jumpers Single configuration jumper design
Jumper access for BIOS configuration mode
Single Front panel USB wake configuration jumper
Jumper allows user to enable ACPI wake from
front panel USB devices
Front Panel Connector Reset, HD LED, Power LEDs, power on/off,
standby header
Mechanical
Board Style µATX 1.0 compliant board size
Board Size 9.2" x 8.2"
Baseboard Power
Requirements ATX12V or SFX12V
Environment
Operating Temperature 0° C to +55° C
Storage Temperature -40° C to +70° C
Regulations
Safety Regulations
U.S. and Canada UL 1950—CSA 950-95
U.S. and Canadian recognition component marks
Europe UL classified to IEC 950
EMI/RFI regulations: Intended for use in systems meeting the following
EMI/RFI regulations:
US FCC Class B (DofC—Cover off testing)
Canada IC Class B
Europe EU Class B (Res, Com, Light Industry)
Japan VCCI, Class B (ITE)
Power requirements vary. Complies with US CRF
via EN55022 + 6db in system configurations with
an open chassis and EU Directive 89/336/EEC
and use via EN55022 and EN50082-1 in a
representative chassis.
Ordering Information—See Intel’s Web site at www.intel.com
For the most current product information available, visit Intel’s Web site at:
www.intel.com/reseller or developer.intel.com/design/motherbd/