Infinity PS210 - Manual (Page 3)

Primus PS210 150W Powered Sub Amp
LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes
US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation
EU 230vac/50-60Hz Yes 207-253 230 Vrms Normal operation, MOMS required
Parameter Specification Unit
QA Test
Limits
Conditions Notes
Amp Section
Type (Class AB, D, other)
D n/a n/a
Load Impedance (speaker) 4 Ohms n/a Nominal
Rated Output Power (120VAC) 150 Watts 145 Domestic version only 120 VAC-60 Hz
Rated Output Power (230VAC) 150 Watts EU Version only 230 VAC-50-60 Hz
AVG RMS Dynamic Power 210 Watts 200
Average RMS power, 3/20 Cycles 50 Hz, Driven
6dB above its input sensitivity sensitivity,
average of the first 4 consecutive peaks
THD @ Rated Power 0.5 % 1 22K filter
THD @ 1 Watt 0.2 % 0.3 22K filter
DC Offset 10 mV-DC 30 Sub amp output
Damping factor >50 DF 35 Measured at amplifier board
Measured at the speaker cable. 150 Watts @
THD < 0.1 % @ 50 Hz
Input Sensitivity-120V
Input Frequency
50 Hz 50 Nominal Freq.
L&R 9.5 mVrms ±1dB To 1 Watt Single input driven
LFE input 9.5 mVrms ±1dB To 1 Watt Single input driven, LFE switch ON
System Gain 46.72 dB Reference Single input driven Normal mode
Input Sensitivity-230V
Input Frequency
50 Hz 50 Nominal Freq.
L&R TBD mVrms ±1dB To 1 Watt Single input driven
LFE input TBD mVrms ±1dB To 1 Watt Single input driven, LFE switch ON
System Gain TBD dB Reference Single input driven Normal mode
Signal to Noise
SNR-A-Weighted
90 dBA 85 relative to rated power A-Weighting filter
SNR-unweighted 80 dBr 75 relative to rated power 22K filter
SNR rel. 1W-unweighted -57 dBr -55 relative to 1W Output 22K filter
Residual Noise Floor 1.5 mVrms(max) 2.5
Volume @max, w/ A/P Swept
Bandpass Measurement (Line
freq.+ harmonics) (BW=20 KHz)
Line level inputs must be terminated using
1KOHM
Input Impedance
Line Input (L, R,LFE)
10K ohms n/a Nominal
Filters
LP filter Variable 50-150 Hz ± 10 2nd order variable + 2nd order fix-24 db/Octave
Subsonic filter (HPF) 2rd Order Fixed 12dB/Octave F=31Hz, Q=2
Friend circuit Fixed 60Hz, Q=2, Av=-3.9dB
LFE Low pass 200>LP<500 Hz LFE input driven only
Limiter
THD at Max. Output Power
N/A N/A functional Maximum Output Power Maximum THD as a result of limiting.
Features --
Volume pot Taper (lin/log) LOG -- functional A Taper
Phase switch 0-180 deg functional
LP Filter defeat switch YES functional Disables LP filter, intended for LFE
Input Configuration
Line In (L,R) & LFE
YES -- functional Dual RCA jack
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
YES functional
ATO Input test frequency 50 Hz functional
ATO Level LFE Input 2.5 mV functional Maximum acceptable level.
ATO Turn-on time 5 ms functional
Amp connected and AC on, then
input signal applied
Auto Mute/ Turn-OFF Time 5-15 minutes 5-15
T before muting, after signal is
removed Auto turn of time (T) must be 5 > T < 15
Minutes
Power on Delay time 3 sec. 4 AC Power Applied
Transients/Pops
ATO Transient 0.5 V-peak 0.5V @ Sub amp output
Amplifier activated by signal presence at the
Line input
Turn-on Transient 0.5 V-peak 0.8V @ Sub amp output AC Line cycled from OFF to ON
PS series PS210 subwoofer
2