Ingersoll-Rand PD30X-X - Manual

OPERATOR’S MANUAL PD30X–X
RELEASED: 9–18–95
REVISED: 6–22–10
(REV. J)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
3” DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Chart to match the pump material options.
637303-XX for Fluid Section Repair (see page 4). Note: This kit also
contains several air motor seals which will need to be replaced.
637302 for Air Section Repair (see page 6).
PUMP DATA
Models See Model Description Chart for ``-XXX''. . . .
Pump Type Metallic Air Operated Double Diaphragm
Material See Model Description Chart. . . .
Weight Aluminum (wet end) 102 lbs (46.3 kgs) . . . . . . . . . .
Cast Iron (wet end) 192.5 lbs (87.3 kgs) . . . . . .
Hastelloy (wet end) 193 lbs (87.5 kgs) . . . . . .
Stainless Steel (wet end) 193 lbs (87.5 kgs) . .
(add 36 lbs [16.3 kg] for stainless steel air motor section)
Maximum Air Inlet Pressure 120 p.s.i.g. (8.3 bar) . . . . . . . . .
Maximum Material Inlet Pressure 10 p.s.i.g. (.69 bar) . . . . .
Maximum Outlet Pressure 120 p.s.i.g. (8.3 bar) . . . . . . . . . . .
Maximum Flow Rate (flooded inlet) 275 g.p.m. (1041 l.p.m.) . . . . . .
Displacement / Cycle @ 100 p.s.i.g. 2.8 gal. (10.6 l) . . .
Maximum Particle Size 3/8" dia. (9.5 mm) . . . . . . . . . . . . .
Maximum Temperature Limits 200_F (93_C) . . . . . . . .
Dimensional Data See page 8 . . . . . . . . . . . . . . . . .
Mounting Dimensions 12" x 13-1/2" (304.8 mm x 342.9 mm) . . . .
Noise Level @ 70 psi, 50 C.P.M.À 83.0 db(A)Б . . . . .
А Tested with 94085 muffler assembly installed.
Á The pump sound pressure levels published here have been updated to an Equivalent
ContinuousSoundLevel (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP
S5.1 using four microphone locations.
NOTICE:All possible options are shown in the chart however certain comĆ
binations may not be recommended, consult a representative or the factoĆ
ry if you have questions concerning availability.
GENERAL DESCRIPTION
The ARO Diaphragm Pump offers high volume delivery even at low air
pressure and a broad range of material compatibility options available.
Refer to the model and option chart. ARO pumps feature stall resistant
design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differential in
the air chambers to alternately create suction and positive fluid pressure in
the fluid chambers, ball checks insure a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will continue to
pump and keep up with the demand. It will build and maintain line presĆ
sure and will stop cycling once maximum line pressure is reached (disĆ
pensing device closed) and will resume pumping as needed.
3'' DIAPHRAGM PUMP
PD30X-XXX-XXX
D005
MODEL DESCRIPTION CHART
PD30 X - X X X - X X X
PD30X - XXX - X X X
637303 - X X
DIAPHRAGM BALL
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: MODEL # PD30A-ACS-SAA
FLUID SECTION SERVICE KIT # 637303-AA
SEAT MATERIAL
A - SantopreneR K - PVDF (KynarR)
G - GeolastR S - 316 Stainless Steel
H - Hard 440 Stainless Steel
DIAPHRAGMMATERIAL
A - Santoprene G - Geolast T -
BALL MATERIAL
A - Santoprene G - Geolast T -
HARDWARE MATERIAL
P - Plated Steel S - Stainless Steel
FLUID CAPS & MANIFOLD MATERIAL
A - Aluminum H - Hastelloy
C - Cast Iron S - Stainless Steel
THREAD
A - NPT B - BSP
CENTER SECTION MATERIAL
A - Aluminum S - Stainless Steel
PTFE
PTFE
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
© 2010
www.ingersollrandproducts.com