JVC XV-N510B - Manual (Page 38)

36
XV-N510B/XV-N512S/GNT0055-001A/English
C
h
a
n
g
in
g
t
h
e
i
n
it
ia
l
s
e
tt
in
g
s
To set the delay time
When playing in multi-channel mode and the speakers cannot all
be located an equal distance from the listener, this setting can
compensate for the difference between the distance from the
front speakers (left, right) to the listener, and the distance from
the center speaker and the surround speakers to the listener.
Check the difference in the distance between the listener and the
front speakers (left, right), and the distance between the listener
and the other speakers, and then set that value as described in
the procedure below.
1
Bring up the SPK.SETTING menu.
2
Press 5/∞ to move to [DELAY] and press
ENTER.
The [DELAY] display page appears on the TV screen.
3
Press 5/∞ to select the speaker to be set and
press ENTER.
CENTER SPEAKER: center speaker
SURROUND SPEAKER: surround (rear) speakers
4
Press 5/∞ to select the appropriate distance
and press ENTER.
When you select [CENTER SPEAKER], you can select the
appropriate distance from [0.0m] to [1.5m] in 30 cm (1 ft)
units.
When you select [SURROUND SPEAKER], you can select
the appropriate distance from [0.0m] to [4.5m] in 30 cm (1 ft)
units.
5
Repeat steps 3 and 4 if you want to set other
speakers.
To return to the [SPK.SETTING] page
Press
5/∞
to move to [RETURN] and press ENTER.
Hint
If there is no difference between the distance from the front
speakers to the listener, and the distance from the center speaker
and/or the surround speakers to the listener, select [0.0m].
If there is a difference between them, refer to the following
diagram to set the delay time correctly.
In the above example, set [CENTER SPEAKER] to [0.3m], and
[SURROUND SPEAKER] to [0.9m].
As the distance from the center speaker and/or the surround
speakers to the listener is shorter than the distance from the front
speakers to the listener, select the longer distance value.
NOTE
This setting can only compensate for differences in speaker
distance when the front speakers (left, right) are farther from the
listener than the other speakers.
To set the speaker level
You can adjust the output level of each speaker.
1
Bring up the SPK.SETTING menu.
2
Press 5/∞ to move to [LEVEL] and press
ENTER.
The [LEVEL] display page appears on the TV screen.
3
Press 5/∞ to select the speaker to be set and
press ENTER.
FRONT SPEAKER: front speakers (This item cannot be
selected. The level is fixed to 0 dB.)
CENTER SPEAKER: center speaker
SURROUND SPEAKER: surround (rear) speakers
SUB WOOFER: subwoofer
4
Press 5/∞ to set the level and press ENTER.
The selectable level ranges from –6 to 6 dB in 1 dB unit.
5
Repeat steps 3 and 4 if you want to set other
speakers.
To return to the [SPK.SETTING] page
Press
5/∞
to move to [RETURN] and press ENTER.
NOTE
For the speaker(s) whose size is set to [NONE], the speaker level
cannot be set.
5/∞
ENTER
Numeric buttons
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS SETUP.
RETURN
DELAY
CENTER SPEAKER
SURROUND SPEAKER
0.0m/0ft
1.5m/5ft
3.0m
2.7m
2.4m
2.1m
Subwoofer
Center speaker
Front speaker
(L) Front speaker
(R)
Surround speaker (L) Surround speaker (R)
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS SETUP.
FRONT SPEAKER 0dB
RETURN
LEVEL
CENTER SPEAKER 0dB
SURROUND SPEAKER 0dB
TEST TONE OFF
SUB WOOFER 0dB
XV-N510B_N512S(JUJ).book Page 36 Monday, March 22, 2004 1:39 PM