JVC DR-MH20B - Manual (Page 48)

Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Left+
48
EN
TIMER RECORDING
Page 48 Thursday, 3 June 2004 10:46
You can programme this unit to timer-record as many as
32 programmes.
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
1
Load a recordable disc if recording to DVD.
2
Press PROGRAMME to access the programme top screen.
3
Press rtw e to select “CALENDAR PR.”, then press ENTER.
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES” appears on the TV screen, you need to cancel
some of the reserved programmes. (
੬ pg. 49)
4
Press rtw e to select the desired date, then press ENTER.
5
Press rt to select “RECORD
TO”, then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
6
Press rt to select “START”, then press ENTER. Press rt to
set the desired start time, then press ENTER.
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press rt to select “STOP”, then press ENTER. Press rt to
set the desired stop time, then press ENTER.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press rt to select “TV PROG”, then press ENTER. Press rt
to select the desired channel.
9
Press rt to select “CONFIRM”, then press ENTER.
10
Set the other recording options as required.
● Refer to step 8 in “VIDEO Plus+ ® Timer Programming” (
੬ pg. 46).
11
Press rt to select “OK”,
then press ENTER to access the
Programme Confirmation screen.
12
Press w e to select “EXIT”,
then press ENTER to complete
timer programming.
● To programme another timer,
press w e to select
“CONTINUE”, then press
ENTER.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 49.
NOTES:
● When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
rtwe
AUX
PROGRAMME
ENTER
CABLE/DBS
DVD TV
14/01/04 WED 22:30 - 23:00 BBC1
[MISC. ] XP
PRESS [PROGRAM]
TO EXIT
[0]: SAT
SELECT WITH [ ]
THEN PRESS [ENTER]
BBC1 TV PROG
23:00 STOP
22:30 START
HDD RECORD TO
PROGRAMME > CALENDAR PROG. (2/3)
CONFIRM
ENTER
SELECT EXIT
PROGRAM
2
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Satellite Receiver Control Setting” (੬ pg. 25).
B Perform “Manual Timer Programming” (੬ pg. 48). In step 8,
press AUX to change “TV PROG” to “SAT”. Then press rt to
enter the channel position for the satellite broadcast.
C Leave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in the same recording mode as set.
● If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
14/01/04 WED 22:30 - 23:00 BBC1
[EDUCATION] GARDENING FR360
1:00 28:00
ENTER
SELECT EXIT
PROGRAM
PRESS [PROGRAM]
TO EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
MON-FRI (FOR A WEEK) WEEKLY/DAILY
OFF VPS/PDC
EDUCATION CATEGORY
GARDENING INPUT TITLE
PROGRAMME > CALENDAR PROG. (3/3)
O K
FR360 REC MODE
2
DR-MH30EU_00.book Page 48 Thursday, June 3, 2004 11:00 AM