JVC RX-9010VBK - Manual (Page 70)

67
English
Operating Video Components
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC video components through the AV
COMPU LINK jacks (see page 62) in addition to the connections
using cables with RCA pin plugs (see pages 8 and 9).
• Some JVC VCRs can accept two types of the control signals —
remote codes “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the VCR
1 terminals is set to code “A.”
– When another JVC VCR is connected to the VCR 2 and VIDEO
jacks, set its remote control code to code “B.” (This remote control
cannot emit the control signals of code “B.”)
• To operate the video component(s) using the remote control:
– Aim the remote control directly at the remote sensor on each
component, not on the receiver.
• To operate the video component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor on the target video component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals at a distance of 10 feet
(3 m).
When using the remote control:
Check to see if MAIN ROOM/SUB ROOM selector and
TV/CATV/DBS selector are set to the correct positions:
• TV/CATV/DBS selector:
To operate TVs, set it to “TV.”
• MAIN ROOM/SUB ROOM selector:
– For the main room operations
Set MAIN ROOM/SUB ROOM selector to “MAIN ROOM.”
– For the sub-room operations
Set MAIN ROOM/SUB ROOM selector to
“SUB ROOM.”
– Check to see if the following information
appear on the display window on the remote control:
VCR (VCR connected to the VCR 1 jacks)
You can always perform the following operations:
VCR 1 POWER : Turns on or off the VCR 1.
After pressing VCR 1 or selecting “VCR” by pressing CONTROL
repeatedly, you can perform the following operations on a VCR:
1 – 9, 0 : Selects the TV channels on a VCR.
PLAY : Starts playing.
REW : Rewinds a tape.
FF : Fast winds a tape.
STOP : Stops operations.
PAUSE : Pauses playing. To release it, press PLAY.
¶ REC : Press this button with the PLAY button to
start recording (only for the main room
operations).
Press this button with the PAUSE button to enter
recording pause.
CHANNEL +/– : Changes the TV channels on a VCR.
Note:
You can use either VCR 1 button or CONTROL to activate the buttons
listed above. If you press VCR 1, the playing source also changes. On
the other hand, if you press CONTROL repeatedly to select “VCR1,”
the playing source does not change.
DVD player
After pressing DVD (or DVD MULTI: only for the main room
operations), you can perform the following operations on a DVD
player:
1 – 10, 0, +10 : Selects the DVD titles or the tracks.
PLAY : Starts playing.
4: Returns to the beginning of the current (or
previous) track.
¢: Skips to the beginning of the next track.
STOP : Stops playing.
PAUSE : Stops playing temporarily. To release it, press
PLAY.
After pressing DVD
MENU (only for the
main room operations),
these buttons can be used
for the DVD menu
operations.
Note:
For detailed menu operations, refer to the instructions supplied
with the discs or the DVD player.
TV
You can always perform the following operations (with TV/CATV/
DBS selector set to “TV”):
TV/CATV/DBS POWER : Turns on or off the TV.
TV VOL +/– : Adjusts the volume.
TV/VIDEO : Sets the input mode (either TV or
VIDEO).
After pressing TV/DBS (with TV/CATV/DBS selector set to “TV”),
you can perform the following operations on a TV:
CHANNEL +/– : Changes the channels.
1 – 9, 0, 100+ : Selects the channels.
RETURN : Alternates between the previously selected
channel and the current channel.
Buttons Indications
VCR 1 VCR 1
DVD or DVD MULTI DVD
TV/DBS TV
CONTROL (repeatedly)
VCR1 = TAPE = CDR =
CDDSC = (back to the beginning)
DVD MENU DMENU
Indications
one of the selected
source names listed
above
VCR1 or TV
Buttons
PLAY
4/REW
FF/ ¢
STOP
PAUSE
1 – 9, 0, +10, 100+
CHANNEL +/–
After selecting a source:
After pressing DVD MENU:
Indications
DMENU
Buttons
%, fi, @, #, SET
When you press the buttons listed above, the corresponding
indication appears for 5 – 10 seconds for your confirmation.
TV
CATV/
DBS
SUB ROOM MAIN ROOM
Indications MAIN ROOM/
SUB ROOM selector
MAIN ROOM
SUB ROOM
MAIN ROOM
SUB ROOM
* MAIN ROOM or SUB ROOM indicator does not appear when no
indicators appear on the display window.
*
*
SET
MENU
DVD
MENU EXIT
TEXT
DISPLAY
EN62-74.RX-9010VBK[C]f 01.4.13, 5:40 PM 67