Jonsered 2149 - Manual (Page 34)

34
– English
Engine
Cylinder volume, cu.in/cm 3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 8500 rpm,
ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length,
inches/cm
Recommended bar lengths,
inches/cm
Usable cutting length,
inches/cm
Chain speed at max.
power, m/sec
Pitch, inch/mm
Thickness of drive link,
inch/mm
Number of teeth on drive
sprocket
TECHNICAL DATA
2149
3,0/49,4
1,73/44
1,28/32,5
2 700
2,3/ 9 000
FHP
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
Walbro
HDA 159A
1,06/0,50
5-10
0,59/0,28
Automatic
10,8/4,9
W: 11,0/5,0
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
Recommended original and replacement
bar and chain combinations
Following is a list of recommended cutting equipment for the
Jonsered chain saw model 2149. The combinations of powerhead,
bar and chain have been investigated in accordance with the
kickback and vibration requirements of ANSI B 175.1 – 1991.
The guide bar nose radius is determined by either the maximum
number of teeth in the nose sprocket or the corresponding maxi-
mum nose radius of a solid bar.
The following list is the chain saw manufacturers recommendations.
There may be other combinations available, which will also achieve
kickback reduction.
As we are listing the maximum guide bar nose radius, you may use
a guide bar with smaller nose radius than in our list. For guide bars
of the same length, all sprocket-nose guide bars of the same pitch
and having the same number of of sprocket teeth may be conside-
red to have equivalent kickback energy. A hard nose bar having the
same length and nose radius as a sprocket-nose bar may be
considered to have equivalent or less kickback energy than the
sprocket-nose bar.
Low kickback saw chain is a chain which has only met the kickback
performance requirements of ANSI B 175.1 safety requirements for
gasoline-powered chain saws when tested on the representative
sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1.
We recommend that you as replacement use the listed chains or
"Low kickback saw chains" which are available at your dealer.
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
´*xl=¶59¨
13 0,325" 10T Jonsered S30 or Oregon 95VP
15 0,325" 10T
16 0,325" 10T
18 0,325" 10T
20 0,325" 10T
13 0,325" 10T Jonsered S25 or Oregon 21VB
15 0,325" 10T
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 0,325" 10T Total/Sabre 528PS
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
Note: For the chains above you are free to choose between
0,050", 0,058" and 0,063" gauge drive link for the corresponding
bar, see table below.
0,050" (1,3 mm) S30 / 95VP 20VB 520PS
0,058" (1,5 mm) – S25 / 21VB 528PS
0,063" (1,6 mm) – 22VB 523PS