JVC BR-DV600UA - Manual (Page 16)

28
V.IN/A.MONI A.OUT COUNTER
DV CTL
TC
UB
CH-1/2
CH-3/4 Y/C
(CPN)
LINE
L
R
MIX MIX
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET SELECT
SHIFT
MENU
HOLD SHIFT A. DUB
ADVANCE PRESET
REW STOP FF
REC PLAY PAUSE
ON/OFF
MENU
OVER
OVER
H M S F
AUD LOCK SP
32k 48k SLAVE PB NDF
SERVO RF
DEW AUTO OFF
HOLD
CH 2/4
CH 1/3
VIDEO CASSETTE RECORDER BR-DV600UA
dB 40 30 20 10 0
7 PLAYBACK
[AUDIO OUTPUT] switch
[PLAY] button [FF] button
[PAUSE]
button
[REC] button
[STOP] button
[OPERATE]
button
[AUDIO MONITOR] switch
Playback preparation
1 Press the [OPERATE] button to turn the power ON.
2 Insert the cassette into the cassette loading slot.
3 Select the audio output channel.
Select output signals with the switch on the front panel or
menu switch.
5 Selection with the switch on the front panel
• Menu switch setting
No. 054 <SLIDE SW FUNCTION> ......... AUDIO
CH1 CH1 CH2
CH1/3 CH1/3 CH2/4
CH3 CH3 CH4
CH1/2 CH1 CH2
CH1/2/3/4 CH1/3 CH2/4
CH3/4 CH3 CH4
CH2 CH1 CH2
CH2/4 CH1/3 CH2/4
CH4 CH3 CH4
R
L
MIX
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
AUDIO switch Connector
MONITOR OUTPUT MONITOR OUT
AUDIO OUT
CH1/3 CH2/4
* To switch video input signals, use the No. 108 <VIDEO INPUT SELECT>
menu switch.
5 Selection with the menu switch
• Menu switch setting
No. 054 <SLIDE SW FUNCTION> ......... VIDEO
CH1 CH1 CH2
CH1/3 CH1/3 CH2/4
CH3 CH3 CH4
CH2 CH1 CH2
CH2/4 CH1/3 CH2/4
CH4 CH3 CH4
CH1/2 CH1 CH2
CH1/2/3/4 CH1/3 CH2/4
CH3/4 CH3 CH4
R
L
MIX
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
Connector
MONITOR AUDIO OUT
OUT
CH1/3 CH2/4
Menu switch
No. 211
<AUDIO
MONITOR> AUDIO
OUTPUT
switch
29
Repeat play
1 Set the No. 311 <AUTO PLAY> and No. 312 <AUTO
REW> menu switches to “ON”.
੬ See No. <311 AUTO PLAY> and No. 312 <AUTO
REW> on pages 21 to 22.
2 Press the [PLAY] button to start playback.
At tape end, the tape is rewound automatically and
playback starts again. This operation repeats each time
the tape ends.
3 To stop Repeat Play, press the [STOP] button.
Playback
1 Press the [PLAY] button.
Video and audio signals are output from each output
connector. Other data recorded on the tape is read out
(time code, user bits, etc.)
2 To stop playback, press the [STOP] button.
3 To temporarily stop playback, press the [PAUSE]
button.
• For fast-forward playback, press the [FF] button
during playback.
• For fast reverse playback, press the [REW] button
during playback.
• You can select whether or not to play sound during
fast-forward playback or fast reverse playback with the
No. 212 <AUDIO OUT AT SEARCH> ON/OFF setting.
Notes:
• If audio dubbing is performed repeatedly on a short
section of the tape, there may be some noise when
this section is played back.
• When a tape recorded on a consumer MiniDV VCR is
played back on this unit, the sound level may be low.
• When the Pause mode continues for more than
5 minutes, the Stop mode is automatically engaged
to protect the tape. If tape remaining time is less
than 3 minutes or the unit is being used in a low-
temperature environment, the Stop mode is
engaged within about 3 minutes. The Stop mode is
also engaged automatically if slow playback
continues for more than 1 minute with the remote
controller or reverse slow playback continues for
more than 20 seconds.