JVC KD-G140 - Manual (Page 4)

4 – EN
INSTALLATION / CONNECTION
When using the optional stay
Install the unit at an angle of
less than 30˚.
Screw (option)
Stay (option) Fire wall
Dashboard
* Not supplied for this unit.
Flat type screws
—M5
× 8 mm (M5 × 3/8")*
Pocket
Flat type screws—M5 × 8 mm (M5 × 3/8")*
Bracket *
Bracket *
Removing the unit In dash-mounting
Before removing the unit, release the rear section.
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place.
Do the required electrical
connections.
Bend the appropriate tabs
to hold the sleeve firmly
in place.
When you stand the unit,
be careful not to damage
the fuse on the rear.
Purple
Front speaker (left)
To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)
Blue with white
stripe
Red To an accessory terminal in
the fuse block
To a live terminal in the
fuse block connecting to the
car battery (bypassing the
ignition switch) (constant
12 V)
Yellow * 2
To the metallic body
or chassis of the car Black
Ignition switch
* 1 Not supplied for this unit.
* 2 Before checking the operation of this unit prior to installation, this
lead must be connected, otherwise the power cannot be turned on.
* 3 Firmly attach the ground wire to the metallic body or to the chassis
of the car—to the place uncoated with paint (if coated with paint,
remove the paint before attaching the wire). Failure to do so may
cause damage to the unit.
* 4 Signal cord (not supplied for this unit)
15 A fuse
Fuse block
Rear speaker (left)
Rear speaker (right)
Front speaker (right)
White with black stripe
Line out Rear ground terminal
Antenna
terminal
Set “L/O MODE” to “WOOFER”
(See “General settings—PSM.”)
You can also connect a subwoofer to
the REAR LINE OUT terminals.
Rear
speakers
Remote lead
Remote lead (blue with white stripe)
To the remote lead of other equipment
or automatic antenna if any
Y-connector * 1
Front speakers
Subwoofer
Set “L/O MODE” to “REAR”
(See “General settings—PSM.”)
You can connect a power amplifier for
rear speakers.
Gray with black stripe
Green
Gray
Green with black stripe
Purple with black stripe
White
JVC Amplifier
ELECTRICAL CONNECTIONS
Typical connections Connecting the external amplifier or subwoofer
INSTALLATION
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Connect only the front speakers if your
speaker system is two-speaker system.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
JVC Amplifier
I
Handles
E
Washer (ø5)
F
Lock nut (M5)
G
Mounting bolt—
M4 x 5 mm (M4 x 1/4");
M5 x 15 mm (M5 x 5/8") H
Rubber cushion
A
Control panel
B
Sleeve
C
Trim plate
D
Power cord
Parts list for installation and connection
J
Remote controller
K
Battery
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this
unit. The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
or
EN_KD-G240_140[J]_f.indd 4 EN_KD-G240_140[J]_f.indd 4 8/15/07 9:53:11 AM 8/15/07 9:53:11 AM