JVC TM-H1950CG - Manual (Page 6)

TM-H1950CG 1-6
No.51961
ENGLISH
Video input/output terminals
Input (IN) and output (OUT) terminals for component
(color deference) or RGB signals.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)
Select component signal :press INPUT SELECT C button
Select RGB signal
:press INPUT SELECT D button
Synchronized signal input/output terminals
Input (IN) and output (OUT) terminals for the vertical,
horizontal or complex synchronized signals.
External sync is available with RGB input only.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)
G on SYNC cannot be used with RGB input.
Audio input/output terminals
Input (IN) and output (OUT) terminals for audio signals.
The IN and OUT terminals are bridge-connected.
Connection terminal (to a Color Video Monitor)
Attach to the connection terminal of your color video
monitor.
1
CONTROLS AND FEATURES
(INPUT CARD: OPTIONAL)
Ⅵ COMPONENT/RGB INPUT CARD (OPTIONAL:
IF-C01COMG)
B/P B /B-Y
G / Y
OUT IN
OUT IN R/P R /B-Y
OUT IN
VD
OUT IN
HD/C S
OUT IN
OUT IN AUDIO
OUT IN
1
2
3
4
2
3
4
Ⅵ
SDI INPUT CARD (OPTIONAL: IF-C01SDG)
AUDIO 2
AUDIO 1
OUT IN
SWITCHED OUT
SDI 1
SDI 2
IN
IN
1
2
3
4
Output terminal for a selected component
serial digital signal
Output terminal for a selected digital signal (the input
displayed on the screen). The output signal is cable-
compensated.
NOTE: When the monitor’s main power is OFF, no digital
signal is output.
In the standby mode, the signal from the SDI 1 terminal is
output.
Input terminals for component serial digital
signals
Input terminals for the digital signal.
Select SDI 1 :press INPUT SELECT C button
Select SDI 2 :press INPUT SELECT D button
Audio input/output terminals
Input (IN) and output (OUT) terminals for the analog
signals corresponding to SDI 1 and SDI 2.
NOTE: This input card cannot decode audio data even if
contained in the input digital signal.
Connection terminal (to a Color Video
Monitor)
Attach to the connection terminal of your color video
monitor.
1
Note:
● The optional input cards shown below cannot be used.
Using any of these cards will void your warranty and may
result in damage or malfunction.
*Video input card (IF-C01PNG)
*HD-SDI input card (IF-C01HSDG)
*HD-SDI input card (IF-C12HSDG)
2
3
4
7
VIDEO A
REMOTE SLOT
AUDIO A
AUDIO B
VIDEO B IN OUT
IN
IN
IN
OUT
OUT
IN OUT
Y/C
OUT
24 23
25
25
25
REAR VIEW
<Rear Panel>
CONTROLS AND FEATURES
(cont’d)
6
Main power switch
Press the switch to turn the main power ON or OFF. When
the main power is ON, the power indicator on the front
panel lights in orange and the monitor enters the stand-by
mode.
I : ON
⅜ : OFF
AC inlet [AC IN]
Power input connector. Connect the provided AC power
cord
t to an AC outlet (120 V AC or 230 V AC,
50 Hz/60 Hz).
To AC outlet
(230 V AC,
50 Hz/60 Hz)
For the United Kingdom
For Europe
23 Power cord
Connects the provided power cord (120 V AC or
230 V AC, 50 Hz/60 Hz) to the AC IN connector
r .
Caution:
In North America (USA and Canada), this monitor comes
with one power cable. In Europe and the United Kingdom,
two power cables are provided (one for use in continental
European countries and the other for the UK). Be sure to
use the power cable that is appropriate for the AC outlets
used in your region. If none of the power cables provided
is suitable, please contact your dealer or qualified service
personnel to obtain the correct type of power cable.
To AC outlet
(120 V AC,
50 Hz/60 Hz)
For U.S.A. and Canada
24
25
(Rear view of
TM-H1950CG shown)