JVC UX-G300 - Manual (Page 2)

Setting the Clock
Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.
• “0:00” flashes on the main display until you set the clock.
1 Press to activate the clock setting mode.
• If you have already adjusted the clock before, press the button repeatedly until the
clock setting mode is selected.
2
or
Adjust the hour, then the minute.
• To exit from the clock setting, press CLOCK/TIMER as required.
• To go back to the previous step, press CANCEL.
Setting the Sleep Timer
When the System is on, press repeatedly to specify the time (in minutes) as follows:
The SLEEP indicator lights up.
• To check the remaining time until the System shuts off, press once.
Turning Off the System Automatically
—AUTO STANDBY function (only for Disc/USB)
Press and hold until the A.STBY indicator lights on the display.
• The A.STBY indicator starts flashing after playback stops.
If no operation is done for about 3 minutes, the System turns off.
• Not applicable for FM/AM/AUDIO IN.
To cancel this function, press and hold again.
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of the Daily Timers.
1 Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON time,
DAILY 2 ON time, or DAILY 3 ON time—as follows:
2
or
1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“TUNER-FM,” “TUNER-AM,” “DISC,” “AUDIO IN,” or “USB.”
4 For “FM/AM”: Select a preset channel.
For “DISC” or “USB”: Select a track. (For MP3/WMA: Select the group, then the track number.)
For “AUDIO IN”: Make the connected device ready for playback.
5 Select the volume.
• You can select the volume level (“VOLUME 0” (VOL MIN) to “VOLUME 40” (VOL MAX) and
“VOLUME – –”). If you select “VOLUME – –,” the volume is set to the last level when the System
is turned off.
3 Turn off the System (on standby).
• When the on-time comes, the System sets the volume gradually to the preset level.
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.
To Turn Off the Daily Timer
1 Press repeatedly to select “DAILY 1,” “DAILY 2,” or “DAILY 3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.
Basic Tuner Operations
To Press Indication/Result
Set the AM tuner
intervals to 9 kHz
spacing On the System only:
Press and hold
4 DOWN, then press when the System is on standby.
Set the AM tuner
intervals to 10 kHz
spacing On the System only:
Press and hold UP ¢, then press when the System is on standby.
Select FM or AM Press repeatedly.
• The selected frequency band appear.
Select a frequency
or
Press and hold for more than 2 seconds.
The System starts searching for stations and stops when a station of sufficient
signal strength is tuned in.
• If an FM program is broadcast in stereo, the S (stereo) indicator lights up (only
when the reception is good).
• Press during searching to stop.
• Press repeatedly to change the frequency step by step.
Tune in to a preset
station
or
Press to select its preset number.
• For presetting stations, see below.
Change the FM
reception mode
(When an FM stereo
broadcast is hard to
receive) Press to improve reception.
The M (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press again.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
1 Tune in to a station you want to preset.
• You can also store the FM reception mode.
2 Press to activate the preset number entry mode.
• Finish the following steps while the indication on the display is flashing.
3
or
Press to select a preset number for the station you want to store.
4 Press to store the station.
5 7
6 8
Troubleshooting Maintenance Specifications
Listening to Digital Audio Player Learning More about This System
Setting the Clock and Using Timers (see page 6)
• You can set the clock and Daily Timer while the Save Mode
is turned on. While setting the clock or Daily Timer, the
display is turning on.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, readjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts playing the
selected source, Daily Timer is canceled.
Listening to FM and AM Broadcasts
Listening to Digital Audio Player
Digital Audio Player
To get the best performance of the System, keep your discs
and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Setting the Clock and Using Timers
Amplifier section
OUTPUT POWER:
60 W (30 W + 30 W) at 4 Ω (10% THD)
Speakers/Impedance:
4 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at “IN LVL1”)
250 mV/47 kΩ (at “IN LVL2”)
125 mV/47 kΩ (at “IN LVL3”)
Digital input: USB MEMORY
Tuner section
FM tuning range: 87.50 MHz - 108.00 MHz
AM tuning range: 530 kHz - 1 710 kHz
(in 10 kHz spacing)
531 kHz - 1 710 kHz
(in 9 kHz spacing)
CD player section
Dynamic range: 88 dB
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
USB storage
USB specification: Compatible with USB 2.0 Full
Speed
Compatible device: Mass storage class
Compatible file system: FAT16, FAT32
Bus power supply:
Max. 500 mA
Speakers
Speaker units: 10 cm cone x 1
Impedance: 4 Ω
Dimensions (approx.): 160 mm x 250 mm x 150 mm
(W/H/D)
Mass (approx.): 1.6 kg each
General
Power requirements: AC 110 V - AC 240 V , 50/60 Hz
AC 240 V , 50 Hz (only Australia)
AC 220 V , 50 Hz (only Hong
Kong)
Power supply to USB mass storage class device:
DC 5 V 500 mA
Power consumption: 20 W (power on)
6.5 W (standby mode)
1 W or less (Save Mode)
Dimensions (W x H x D): 165 mm x 251 mm x 269 mm
Mass:
2.6 kg
Specifications and appearance are subject to change
without prior notice.
To audio output (or
headphone out, etc.) Stereo mini plug cord
(not supplied)
Radio Operations
Hard to listen to broadcasts because of noise. \ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
\ Electrostatic discharge from your body may cause noise. If
this happens, turn off and on the System again.
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
1 Turn the volume to minimum.
2 Press repeatedly to select “AUDIO IN.”
3 Start playing the Digital Audio Player connected.
4 Adjust the volume.
To Adjust the Audio Input Level
If the sound from the Digital Audio Player connected to the AUDIO IN jack is too loud or too quiet, you can change the audio
input level through the AUDIO IN jack (without changing the volume level).
Press and hold for more than 2 seconds while “AUDIO IN” is selected as the source.
You can select one of three levels as follows:
As the number increases, the sound becomes louder.
Basic and Common Operations (see page 3)
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
Playing Back a Disc/USB Mass Storage Class Device
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used
for MP3/WMA operations.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at bit rate of less than
64 kbps.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
does not include MP3/WMA tracks, they are ignored.
• Do not use the following USB devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabyte.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
• This System can recognize up to 99 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 9 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The disc is recorded with the “packet writing (UDF file
system).” It cannot be played. Check the files you want to
play back.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Sounds from USB mass storage class device are
interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has
the same or similar button names, they can also be used for the operations. Display Information
Play mode indicators (See page 4.)
Main display
A.STBY (Auto Standby) indicator (See page 6.)
AHB indicator (See page 3.)
Source indicators (See page 3.)
Timer mode indicators
(See page 6.)
SLEEP indicator (See page 6.) File type indicators (See page 4.)
FM reception indicators (See page 5.)
Source indicators (See page 3.)
S.TURBO (Sound Turbo) indicator (See page 3.)
Surround mode indicator (See page 3.)
The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has
the same or similar button names, they can also be used for the operations.
Front view
The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has
the same or similar button names, they can also be used for the operations.
GVT0241-015A EN_UX-G300[US/UB/UG/A/UW]4