JVC SP-X60 User Manual
Page 2
2
Connection
Anschluß
Raccordement
Aansuluiting
Conexión
CONNECTION
• Connect the CENTER speaker terminals of the amplifier to the terminals
of the SP-XC60 using the attached speaker cords as shown in the figure
making sure polarity is correct; (+) to (+) and (–) to (–).
Connect the black speaker wire to the (–) terminal.
• Connect the LEFT SURROUND speaker terminals of the amplifier to the
LEFT terminals of the SP-XS60 and RIGHT to RIGHT using the attached
speaker cords as shown in the figure making sure polarity is correct; (+) to
(+) and (–) to (–).
Connect the black stripe speaker wire to the (–) terminal.
• Turn off power of all equipment before connecting the speakers to the
amplifier.
• The nominal impedance of the SP-XC60/SP-XS60 is 8 ohms. Select for
use an amplifier to which a speaker system with the load impedance of 8
ohms can be connected.
• The maximum power handling capacity is shown in the SPECIFICATIONS.
Excessive input to the speaker will result in abnormal noise and possible
damage. The following cases described below may cause an overload of
the speakers. Be sure to lower the amplifier volume beforehand.
1)
Noise during FM tuning.
2)
High level signals containing high frequency components prouduced
by a tape deck in the fast forward mode.
3)
Click noise produced when turning power of other components on
and off.
4)
Click noise produced when connecting or disconnecting cords with
the power on.
5)
Click noise when the cartridge is replaced with the power on .
6)
Click noise produced when operating amplifier switches.
7)
Continuous high frequency oscillation or high pitch musical instrument
sound.
8)
Howling or feed back when using a microphones.
SPEAKER FOR A/V COMBINATION
SP-XC60 have a magnetically-shielded design for placement adjacent to TVs
and monitors without causing color aberrations. However, color may be af-
fected as a result of how the speaker system is installed. Therefore, be care-
ful of the following:
1. When placing these speakers near a TV set, turn off the TV’s main power
switch or unplug it before installing the speakers.
Wait at least 30 minutes after the system is installed before turning on the
TV’s power.
2. If another speaker system has been set up near the TV set, that system
may cause color unevenness in the TV’s picture.
3. In spite of the shielded design of these speakers, some types of TV’s may
be affected by them. If this happens, move the speakers a short distance
form the TV set.
HOW TO INSTALL SURROUND SPEAKERS
• This equipment is not magnet-proof. If it is placed near a TV set, color on
a TV screen may become uneven. If the case of installation, therefore,
locate it at sufficient distance from the TV set.
• The speakers of this system are designed to stand on the side or on the
bottom, whichever you prefer.
• When setting the speaker on such as a high shelf, be sure to fix them to
the shelf by using such as metal braces: this a precaution against the
speakers falling off due to shelf trembling.
• You may hitch the speakers to the wall, holding them horizontally or verti-
cally. The back of each speaker has a hole for catching the hook.
SPECIFICATIONS
SP-XC60
Type
: 2-way 3-speaker bass-reflex
type
(Magnetically-shielded type)
Speakers
Woofer
: 9 cm (3-9/16") cone
×
2
Tweeter
: 5 cm (2") cone
×
1
Power Handling Capacity
: 120 W
Impedance
: 8
Ω
Frequency Range
: 65 Hz - 20,000 Hz
Sound Pressure Level
: 88 dB/w·m
Dimensions (W
×
H
×
D)
: 390
Ч
146
Ч
141 mm
(15-3/8"
Ч
5-3/4"
Ч
5-9/16")
Mass
: 3.0
kg
(6.7 lbs)
Accessories
: Speaker cord (3m)… 1
SP-XS60
Type
: Full range Acoustic-suspension type
Speaker
Full range
: 10cm (4") cone x 1
Power Handling Capacity
: 100 W
Impedance
: 8
Ω
Frequency Range
: 75 Hz – 20,000 Hz
Sound Pressure Level
: 85 dB/w·m
Dimensions (W x H x D)
: 147 x 215 x 141 mm
(5-13/16" x 8-1/2" x 5-5/8")
Mass
: 1.6
kg
(3.6 lbs) each
Accessories
: Speaker cord (6m)… 2
Design and specifications subject to change without notice.
1. Remove the ending part of the vinyl covering from
the cut.
2. Twist the wires.
1. Entfernen Sie dan Endstück der Vinylhüle von dem geschnittenen Teil.
2. Drehen Sie die Kabel.
1. Enlever la partie d'extémité du recouvrement
vinylique de la partie déoupée.
2. Tordre les fils.
1. Snijd het laatste gedeelte van de
vinylmantel af en verwijder.
2. Draai de draadkernen ineen.
1. Remover la parte de extremidad de la
cubierte de plástica de la parte cortada.
2. Torcer los alambres.
1. Rimuovere la parte di estremità della
copertura in plastica dalla parte tagliata.
2. Torcere i fili.
1. Dra loss den avskurna delen av isoleringen från kabeländen.
2. Tvinna trådarna.
1. Fjern enden af vinyl-isoleringen, hvor den er klippet af.
2. Sno trådene.
1. Irrota muovipeiteen loppupåå uurteesta.
2. Kierrä johdot.
SP-XC60
Black
Noir
Schwarz
Zwart
Negro
Nero
Svart
Sort
Musta
SP-XS60
Black stripe
Schwarzer Streifen
Raie noire
Zwarte streep
Banda negra
Righe nere
Svart rand
Sort stribe
Nusta juova
Press
Appuyer
Drücken
Indrukken
Presioar
Premere
Tryck
Trk
Paina
➤
➤
• Pull aside the speaker cord from
the space between the wall and the
speaker. This will stabilize the
speaker.
• Ziehen Sie das Lautsprecherkabel
aus dem Raum zwischen der Wand
und dem Lautsprecher. Hierdurch
wird der Lautsprecher stabilisiert.
• Eloigner le cordon d’enceinte de
l’espace entre le mur et l’enceinte.
Cela stabilisera l’enceinte.
• Trek het luidsprekersnoer opzij uit
de ruimte tussen de muur en de
luidspreker. Hierdoor wordt de
luidspreker gestabiliseerd.
• No pase el cable del altavoz entre
éste y la pared. Esto estabilizará
el altavoz.
• Allontanare il cavo di altoparlante
d a l l o s p a z i o t r a m u r o e
altoparlante. Questo ser ve a
stabilizzare l’altoparlante.
• Dra undan högtalarkabeln från
mellanrummet mellan väggen och
högtalaren för att stabilisera
högtalaren.
• Træk højttaler kablet væk fra
p l a d s e n m e l l e m v æ g g e n o g
højttaleren. Dette vil stabilisere
højttaleren.
• Ve d ä k a i u t i n j o h t o s e i n ä n j a
k a i u t t i m e n v ä l i s t ä . T ä m ä
vakiinnuttaa kaiuttimen.
Wall mounting hole
Wandanbringungsloch
Orifice de montage
mural
Bevestigingsgat muur
Orificio para montaje
en una pared
Foro di montaggio a
muro
Väggmonteringshål
Monteringshul i
væggen
Seinäasennusaukko
Collegamento
Ansluiting
Tilslutning
Liitäntä
1 – 1.5 cm
…
¢
Ł-1
00.2.21, 10:58 AM
2