JL Audio Stealthbox SB-GM-SLVEXT/10W6v2 - Manual (Page 2)

Specifications:
Enclosure Type: Ported
Driver Type: 10W6v2-D4
Nominal Impedance: 2
Ω per woofer / can be rewired for 8 Ω per woofer
Cont. Power Handling: 400Watts per woofer / 800Watts for system
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1 or the JL Audio 1000/1. The diagram below shows
the recommended crossover, infrasonic filter and equalizer settings for either the 500/1 or the 1000/1 when being used to power
your Stealthbox®.
Included Hardware:
1) 3” x 3’ wax Square
1) 3/8”-16 x 2-1/4” Socket Cup Set Screw
1) 3/8” x 1-1/4” Fender Washer
1) 3/8” Flat Washer
1) 3/8” Split Lock Washer
1) 3/8” - 16 Hex Nut
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111
+12VDC Remote Ground
JL AUDIO 500/1
five-channel system amplifier
+ _ _ +
Subwoofer Output
MONO OUTPUT ONLY 40
45
55 65 85
120
200
Filter Freq. (Hz)
Mode / Slope
Off / 12dB / 24dB
Amp LP Filter
Infrasonic Freq. (Hz)
15
18
25 30 40
50
60
Off / 30Hz
Infrasonic Filter
0.5
0.7
1.1 1.6 2.7
4.3
"Q"
20
25
35 45 55
70
85
Center Freq.
0
+4 +10 +13
+15
Boost (dB)
Off / On
Bass EQ
Remote Bass Port
Advanced
Bass
Control
Preamp Output Section
Full Range / Amp Filter / Out Filter
Output Mode Filter Slope
12dB / 24dB
40
45
55 65 85
120
200
Filter Freq. (Hz) Left Ch. Right Ch.
Filter Mode
LP / HP
Amplifier Input Section
Input Sens.
Left Ch. Right Ch.
Signal Sensing
Off / On
Input Voltage
Low / High
The JL Audio 500/1 or the JL Audio 1000/1 is a very versatile audio component. Please consult the owner’s manual for
detailed information about installing and tuning this amplifier.
➔ ➔ ➔
STEP 6: Run speaker wire to the/each enclosure
and attach to the speaker terminal cup. Check the
woofer(s) for proper operation at this time.
STEALTHBOX WALL THREADED INSERT
VEHICLE SHEET METAL
FENDER WASHER SOCKET CUP SET SCREW
LOCK WASHER
FLAT WASHER
HEX NUT
STEP 7: Back out the/each socket cup set screw
to expose about 1-1/2”.
Place the socket cup set screw through the mount-
ing hole that was drilled, inside the truck.
From the under side of the truck, place a supplied
fender washer, flat washer, lock washer and then hex
nut onto the/each socket cup set screw.
Secure tightly, using a 14mm socket and ratchet.
STEP 8: Lower the rear seat and replace all
removed contents.
➔
S B - G M - S X T / 1 0 W 6 v 2 , J L AU D I O, I n c 2 0 0 6 S h e e t S K U # 0 1 1 1 9 9 R ev i s i o n 1 / 1 2 / 2 0 0 6 Pa g e 2 w w w . j l a u d i o . c o m
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
ZR650-CSi
TR400-CXi
Front Location Driver Size:
6.5” Separates
Applicable JL Audio Products:
TR,VR,XR & ZR650-CSi
Rear Location Driver Size:
4”x 6”
Applicable JL Audio Products:
TR400-CXi
Cont.
From
Previous
Page
Difficulty Of Installation: