Jacuzzi K272000AF 7/06 - Manual (Page 25)

E
N
G
L
IS
H
Operation
NOTE: These instructions pertain to all Builder/Comfort bath products manufactured by Jacuzzi Whirlpool Bath. Not all features
discussed in this instruction booklet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained after each use
and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools
or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas
available.
Once the bath is installed, remove any residue or foreign materials left over from construction. Paint, tar, or other difficult surface stains can
be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). NOTE: Use these chemicals only on SURFACE stains. Other dirt
can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or plastic edge; do not use metal scrapers,
wire brushes or other metal tools, as they will damage the bath's surface.
Water Level
Close the drain and fill the bath until water is at least 1" to 2" (25,4 mm - 50,8 mm) above the highest jet (see water line indicated in the
illustration). Do not turn on the whirlpool system at any time if the jets are not completely immersed in water. Do not immerse the
control panel by overfilling the bath. Running the whirlpool system when there is insufficient water in the bath could result in water spraying
outside the bath area. Running the whirlpool system without water will damage the recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop below the jets which could result in water being sprayed out of the unit. To prevent
this, you must turn unit off before exiting bath.
WATER RAINBOW
FILL SPOUT (OPTIONAL)
MAGIC TOUCH WHIRLPOOL
ON/OFF SWITCH
AIR CONTROL
KNOBS
DRAIN/OVERFLOW
(OPTIONAL)
FULLY ADJUSTABLE JETS
TYPICAL BATH FITTINGS
SUCTION
COVER
(Optional) RapidHeat TM
Operation
Once the heater is installed and the whirlpool pump is operating,
the heating function is totally automatic. The heater will help main-
tain the temperature of the water in the bath.
Vacuum or Pressure Switch
The heater is equipped with a preset vacuum switch or pressure
switch which will not allow the heater to turn ON if the pump is not
running with water flowing through the whirlpool system.
High-Limit Switch
The heater includes an exclusive High-Limit switch. This safety
circuit will not false trip from hot tap water. It will only turn off the
heater if the thermostat fails. To reset, press the button. If the high-
limit trips frequently, contact your Authorized Electrical/Mechanical
Service Provider. Visit our web site at
http://www.jacuzzi.com/ to
find a Service Provider.
OPERATING INSTRUCTIONS
1" - 2"
FILL TO AT LEAST
1" - 2" (25,4 mm - 50,8 mm)
ABOVE HIGHEST JET
25
Jacuzzi Whirlpool Bath K272000AF 7/06
PUSH TO RESET
OVER HEAT
PROTECTION
HIGH LIMIT RESET
HEATER ON
HEATER ON
WATER RAINBOW
FILL SPOUT (OPTIONAL)
ELECTRONIC
CONTROL
SWITCH
DRAIN/OVERFLOW
(OPTIONAL)
FULLY ADJUSTABLE JETS
TYPICAL BATH FITTINGS
SUCTION
COVER
Export units come equipped with the Magic Touch ® Whirlpool ON/
OFF switch. Refer to the Magic Touch ® Whirlpool Switch instructions
on the next page.
Jacuzzi builder/comfort units come equipped with electronic con-
trols. Refer to the Electronic Controls instructions on the next page.