JVC DLA-M4000LU - Manual (Page 7)

No.51666
DLA-M4000LU DLA-M4000LE
12
Controls and Features (Cont.)
Remote Control Unit
MEN U/E N T E R
QUICK ALIGN. AV HIDE OPERATE
PRESET
AV
SHIFT ZOOM FOCUS
LENS
U T +
D W –
RGB/COMPUTER
LENS
LOCK
UNLOCK
PAGE BACK
MEN U/E N T E R
QUICK ALIGN. AV HIDE OPERATE
PRESET
AV
SHIFT ZOOM FOCUS
LENS
U T +
D W –
RGB/COMPUTER
LENS LOCK
UNLOCK
PAGE BACK
VOLUME –
+
r
8
e
w
p
9 6
5
4
3
2
1
t
q
7
p AV button
Use this button to select the devices such as a video
connected to the projector’s AV IN (EXT. input) terminal.
Each time you press the button, the selection changes as
follows:
Y/C VIDEO YPBPR
* Y/C and VIDEO can be used only when a video board
separately sold has been installed.
q LENS LOCK Ô UNLOCK switch
With this switch set at the LOCK position, adjustment
operations (focus, zoom or shift) with the remote control
are disabled, preventing adjustment contents from being
inadvertently changed while the remote control is being
used. When adjustment is needed, set the switch to the
UNLOCK position.
w PRESET button
While making adjustment on the main or setting menu,
use this button to reset the setting of the selected item to
the factory-set value. This button works only for numerical
settings and does not work for switching ON to OFF.
e QUICK ALIGN. (Quick Alignment) button
Use this button to automatically adjust TRACKING,
PHASE, H. POS. and V. POS. of the projected video.
During the automatic adjustment, QUICK ALIGNMENT
appears on the screen, and disappears after it is finished.
Memo
Quick alignment function:
Does not work for video input (EXT. IN input terminal) signals.
Works only for computer-related (RGB-1 and-2 input terminals)
signals.
CAUTION
• Automatic adjustment with the quick alignment function should be
done on a bright still-picture screen. This function may not work
correctly on a dark screen or motion-picture screen. If adjustment
with this function is not satisfactory, adjust TRACKING, PHASE, H.
POS. and V. POS. manually (see pages 30, 36 and 37).
r AV HIDE button
Use this button to turn off the video image temporarily.
Pressing it again makes the video image to resume.
t Not used with this projector
* *
13
Controls and Features (cont.)
MENU / ENTER (Menu Operation) Button
Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries.
1 Open the back cover.
Open the back cover in the direction of the arrow.
2 Install the batteries.
Place the two batteries (AA/R6-size) supplied in the remote
control as illustrated below.
Precautions for using batteries
If batteries are used incorrectly, they may crack or
leak liquid. This could cause a fire, burn, malfunction,
or staining or damaging the surrounding.
Beware of the following:
• Do not mix new and old batteries.
• Do not mix different types of batteries as they differ in
characteristics.
• Place batteries so they match the polarities indicated:
(+) to (+) and (–) to (–).
• Be sure to put the minus (–) end in first to avoid short-
circuiting.
• Use only designated batteries.
• Remove the batteries if not used for a prolonged period
of time.
• When the batteries are exhausted, replace them
immediately. Otherwise, liquid could leak, or malfunction
could occur due to leaked liquids. If the leaked liquid
contacts the skin, wipe it off with a cloth, otherwise the
skin could become rough.
• Do not put batteries into fire or try to recharge them.
• Batteries run for six months to one year in normal use.
But the batteries supplied are for confirming operation
and may not run that long. When the remote control starts
failing to work properly, replace the batteries with new
ones.
1
2 2
2
2
3 Close the back cover.
First fit the claw on the back cover into the case, then
close the back cover in the direction of the arrow.
The remote control supplied with this projector has only one button to navigate through the menus. Pressing the menu operation
button too strongly may cause an incorrect operation. So, before you use the button in an actual situation, have some practice
to make yourself familiar with using the button.
1
When using the MENU/ENTER button as a menu
operation button :
Press the button down straight when displaying the main
menu. While the main menu is displayed, if the selected
item has a details setting (submenu), pressing the button
will cause the submenu to be displayed.
2
When using the MENU/ENTER button as a cursor
moving button:
Press the button toward one of the
5 / ∞ / 2 / 3 marks.
While the main menu is displayed, use the button to select
an item to adjust or make adjustment.
ª
ª
·
·
Installing Batteries