Sony SPP-Q110 - Manual (Page 2)

SPP Q110/Q120 3 856 344 11 E U
CAUTION: TO REDUCE THE RISK OF FIRE OR INJURY TO
PERSONS BY BATTERY, READ AND FOLLOW THESE
INSTRUCTIONS.
1. Use only the following type and size battery pack: SONY BP-T16.
2. Do not dispose of the battery pack in a fire. The cell may explode.
Check with local codes for possible special disposal instructions.
3. Do not open or mutilate the battery pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic if
swallowed.
4. Exercise care in handling battery in order not to short the battery with
conducting materials such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
5. Charge the battery pack provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the battery pack and
battery charger.
INFORMATION FOR GENERAL
TELEPHONES
(1) This equipment complies with Part 68 of the FCC rules. On the
bottom of this equipment is a label that contains, among other
information, the FCC registration number and ringer equivalence
number (REN) for this equipment. If requested, this information
must be provided to the telephone company.
(2) The applicable registration jack (connector) USOC-RJ11C is used for
this equipment.
(3) This equipment is designed to be connected to the telephone
network or premises wiring using a compatible modular jack which
is Part 68 compliant.
The FCC compliant telephone cord and modular plug is provided
with this equipment.
(4) The REN is used to determine the quantity of devices which may be
connected to the telephone line. Excessive RENs on the telephone
line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the REN’s should not
exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the
local telephone company.
(5) If your equipment (SPP-Q110 or SPP-Q120) causes harm to the
telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required.
But if advance notice isn’t practical, the telephone company will
notify the customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is
necessary.
(6) The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the operation
of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
(7) If trouble is experienced with this equipment (SPP-Q110 or SPP-
Q120), for repair or warranty information, please contact Sony Direct
Response Center: Tel 1-800-222-7669. If the equipment is causing
harm to the telephone network, the telephone company may request
that you disconnect the equipment until the problem is resolved.
(8) All repairs will be performed by an authorized Sony service station.
(9) This equipment cannot be used to party lines or coin lines.
(10) This equipment is hearing aid compatible.
If your telephone is equipped with automatic dialers
When programming emergency numbers and (or) making test calls to
emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for
the call.
2. Perform such activities in the off-peak hours, such as early morning
or late evenings.
CAUTION
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
CAUTION
The cordless telephone operates at a frequency that may cause
interference to nearby TVs and VCRs; the base unit should not be placed
near or on the top of a TV or VCR; and, if interference is experienced,
moving the cordless telephone farther away from the TV or VCR will
often reduce or eliminate the interference.
Note
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Choose the dialing mode
For the telephone to work properly, select an appropriate dialing
mode (tone or pulse).
Depending on your dialing system, set
the DIAL MODE switch as follows:
DIAL MODE switch
If your dialing system is
Tone
Pulse
Set the switch to
T
P
If you aren’t sure of your dialing system
Make a trial call with the DIAL MODE switch set to T.
If the call connects, leave the switch as is; otherwise, set to P.
Setting up the phone
Connect the base unit
If you want to hang the base unit on the wall, mount the unit first
(see “Mounting your phone on the wall”).
1
Connect the telephone line cord to the TEL LINE jack and to a
telephone outlet.
2
Connect the AC power adaptor to the DC IN 9V jack and to an AC
outlet.
3
Fully extend the antenna. Make sure it points toward the ceiling.
Notes
• Use only the supplied AC-T56 AC power
adaptor. Do not use any other AC power
adaptor.
• Connect the AC power adaptor to a continuous
power supply.
• Place the base unit close to the AC outlet so that
you can unplug the AC power adaptor easily.
Tip
If your telephone outlet is not modular, contact your telephone service
company for assistance.
Polarity of the plug
Modular
To telephone
outlet
Telephone line cord
(supplied)
To AC outlet
1
2
3
AC power adaptor (supplied)
To TEL
LINE
jack
To DC IN 9V
Hook