Solid State Logic AMETRIX 1266 - Manual (Page 2)

Important Safety and Installation Instructions
This section contains definitions, warnings, and practical information to ensure a safe working environment.
Please take time to read this section before installing or using this unit. Please do not dispose of these instructions.
Please take time to read this section before installing or using this unit. Please do not dispose of these instructions. Please take time to read this section before installing or using this unit. Please do not dispose of these instructions. Please take time to read this section before installing or using this unit. Please do not dispose of these instructions.
2222
•
Read these instructions
•
Keep these instructions
•
Heed all warnings
•
Follow all instructions
•
Do not use this apparatus near water
•
Do not expose this apparatus to rain or moisture.
•
Clean only with a dry cloth
•
Do not block any ventilation openings. Install with accordance
with the manufacturer’s instructions.
•
No naked flames, such as lighted candles, should be placed
on the apparatus.
•
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers) that
produce heat.
•
There are no user-adjustments, or user-serviceable items,
inside this apparatus. Do not remove the covers of this
apparatus; doing so will invalidate your warranty.
•
Adjustments or alterations to this apparatus may affect the
performance such that safety and/or international compliance
standards may no longer be met.
•
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally or has been dropped.
Caution
Caution Caution Caution
•
Hazardous voltages may be present inside this apparatus.
•
Do not operate this apparatus with the covers removed.
•
To reduce the risk of electric shock, do not perform any
servicing other than that contained in these Installation
Instructions unless you are qualified to do so. Refer all
servicing to qualified service personnel and ensure that all
power cords are disconnected when servicing this apparatus.
•
Only use attachments/accessories specified by the
manufacturer.
Power Safety
Power Safety Power Safety Power Safety
•
This apparatus is fitted with a universal power supply,
approved and certified for operation in this apparatus. There
are no user-replaceable fuses.
•
An external over-current protection device is required to
protect the wiring to this apparatus. This protection device
must be installed according to current wiring regulations. In
certain countries this function is supplied by use of a fused
plug.
•
If an extension power cable or adaptor is used, ensure that
the total power rating of the power cable and/or adaptor is not
exceeded.
•
An external disconnect device is required for this apparatus; a
detachable power cord is a suitable disconnect device.
•
The apparatus should be located close enough to an AC outlet
so that you can easily grasp the power cord plug at any time.
•
This apparatus is a Class I construction and shall be
connected to an AC outlet with a protective grounding
connection.
•
Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
•
Unplug this apparatus during lightning storms or when
unused for long periods of time.
•
All power cords must be disconnected to isolate this
apparatus completely.
•
Caution: To reduce the risk of electric shock, plug each power
supply cord into separate branch circuits employing separate
service grounds
•
This equipment is not supplied with a detachable power cord.
The device should be connected to a power supply only of the
type described in the Installation Guide or as marked on the
device. The power cord must be earthed and precautions
should be made so that the grounding is not defeated. A
mains cord, fitted with an IEC 60320 C13 type socket,
appropriate sized conductors and plug to suit local electrical
requirements.
•
The power supply cord (i.e. conductor, coupler [IEC 60320 C13]
and plug combination) must be suitably rated for the
apparatus and the country of use (meeting local electrical
requirements). A power supply cord with a rating of not less
than 125% of current rating is suitable. The minimum rating
for the power supply cord at 110 / 230V ac to be 1A.
Installation
Installation Installation Installation
•
When installing this apparatus, either fix it into a standard 19”
rack or place the apparatus on a secure level surface. When
this apparatus is rack mounted, fit all rack screws.
•
Ensure that no strain is placed on the cables connecting to
this apparatus. Ensure also that such cables are not placed
where they can be stepped on, pulled or tripped over.
•
Do not operate this apparatus whilst it is covered or boxed in
any way.