Swann Night Hawk - Manual (Page 3)

The Camera features an omni-directional antenna which is most effective when use
in the UPRIGHT position.
1)
2)
3) After connecting both the Night Hawk Camera and the Receiver make sure the receiver
is switched to the same channel as the camera.
channel 1.
SEL Ch1
Normal
4)
Connect both the Camera and the Receiver to their respective power adaptors.
Connect the Receiver to the equipment you wish to view the camera on (monitor, AV TV,
VCR, DVR etc) using the supplied A/V-RCA cable.
By default the camera is set to
Press the button on the receiver until the LED for is lit. If the channel LEDs flash and
the receiver scans through all 4 channels, switch the Loop/Normal selector at the back of the
receiver to
. Obtain the best picture by adjusting the position of the Night Hawk
camera and Receiver unit to suit. Try slightly different locations of either unit for optimum
results.
If you are mounting the camera to a ceiling or eave, unscrew the camera stand from the
camera body and carefully screw it into position on the top side of the camera using the two
holes that are provided or the picture will appear on your screen upside down.
Camera with Stand
Camera Power Adaptor (8V)
Receiver
External antenna
Audio / Video Out
To Audio and
Video IN
Monitor or TV
DC Socket
Channel
Selector
Button
Loop / Normal Switch
Active
Channel
Leds
SEL
CH2
CH4
CH1
CH3
Receiver Features
Receiver
Power Adaptor
Poor Picture:
Lines only - no clear picture:
Picture ghosting or interference:
No picture
Realign antennas until image quality improves, slightly adjust the position of the Night Hawk
Camera or Receiver. Change the location of the Camera, or use a different Camera in the location
experiencing interference that is on a different channel. In some cases interference may be caused by
another device on a similar frequency to the channel you are using. Change to one of the other channels
and check the signal quality again.
Check to confirm there is no microwave oven or other 2.4GHz
equipment operating close by ie; Cordless Telephones, Wireless Baby Monitors, Wireless LAN
equipment etc. Make sure the Receiver is on the correct channel for the particular camera.
Some home appliances such as Wireless LANs, 2.4GHz portable
telephones and Microwave ovens operate on or near the 2.4GHz frequency. If you receive interference
from such an appliance, try moving the Camera or Receiver to location further away from the appliance
or in the event of interference from a Wireless LAN device,
try changing the Wireless LAN to a different channel to improve the signal quality.
: check the receiver to confirm it is turned ON and make sure the A/V connection of the
Receiver is not plugged into the Audio Out socket. Make sure the Receiver is on the correct channel.
Check to ensure the camera is plugged in and has power (cup your hands around the camera and you
should see a faint red glow from the IR LEDs). Check that the channel on the receiver is the set to the
same as the camera you wish to view.
3 6
Troubleshooting your Night Hawk Camera Setting Up Your System
FCC Notice
CE Notice
L V D
We, Swann Communications of 10612 Shoemaker Avenue, Bldg A, Santa Fe Springs, CA 90670 USA,
declare under our sole responsibility that the product:
This product meets the requirement specified in Part 15 of FCC Regulation. Operation rests with the
following two conditions:
(1) The equipment should not cause any harmful interference;
(2) The equipment must receive and process any interference, including any possible interference
caused by operation mistakes. After testing the product, we confirm that it complies with the provision
for class C digital equipment in the 15th part in FCC regulation; and the receiver complies with the
limitation for class B digital equipment in Part 15 of FCC regulation. The product generates, applies and
emits radio waves. It might cause harmful interferences to wireless communication if not be installed
and used following the description of the manual. The product may interference in residential area, and
the customer should take remedies to eliminate the interference at their own costs. If the product
causes any harmful interference to wireless equipment of disturbs the receiving of TV signals (it can be
identified by turning on and off the product), you can solve the trouble by following methods:
(1) Re-adjust the product or put it in another place;
(2) Extend the distance between the equipment interfered and the product; and
(3) Refer to dealers or experienced radio electrician for help
This product complies with standards including ow oltage evice Directive 73/23/EEC;
Directive 89/336/EEC and Directive 1999/5/EC. It passed the subject tests by authority
concerned and it authorized to bear mark.
SW231-WOC
EMC
R&TTE
CE