Southbend 16" X 40" LATHE 220V w/DRO SB1037F - Manual

Manual Insert
PHONE: (360) 734-1540 • www.southbendlathe.com
MODEL SB1037F
16" X 40" LATHE 220V w/DRO
Copyright © June, 2011 by South Bend Lathe Co.
WARNING: No portion of this manual may be reproduced without written approval.
#BL14237 Printed in USA
The Model SB1037F Lathe is the same machine as the Model SB1037 except for the following:
• Added a 2-Axis Fagor Digital Readout (DRO).
Except for the differences noted in this insert, all other content in the Model SB1037 Owner’s Manual
applies to this machine. Before operating your new lathe, you MUST read and understand this insert,
the entire Model SB1037 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of
injury when using this machine. Keep this insert for later reference.
If you have any further questions about this manual insert or the differences between the Model
SB1037F and the Model SB1037, contact our Technical Support at (360) 734-1639 or email
[email protected].
REF PART # DESCRIPTION REF PART # DESCRIPTION
2318 PSB1037F2318 DRO ASSEMBLY FAGOR 2-AXIS 2318-3 PSB1014F2318-3 DRO Y-AXIS SCALE FAGOR MKT-27
2318-1 PSB1014F2318-1 DRO DISPLAY FAGOR 20-iT 2407 PSB1037F2407 MACHINE ID LABEL
2318-2 PSB1037F2318-2 DRO X-AXIS SCALE FAGOR MKT-102 2416 PSB1037F2416 MODEL NUMBER LABEL
New & Changed Parts
Made in T aiwan to South B
end Spec ifica tions
MODEL SB1037F 16" x 40" EVS
TOOLR
OOM
LATHE
w/DR
O
MFG Date
Serial Nu
mber
TO REDUCE THE RISK OF SERIOUS PERSONA
L INJUR
Y WHILE USING THIS
MA CHINE:
1. Read and understand manual bef
ore star
ting .
2. Always wear appro
ved eye protec
tion.
3. Make sur
e the mac
hine is connec
ted to a grounded po
wer sourc
e.
4. Keep all guards in place.
5. DO NO
T wear loose c
lothing
, glo ves , or je welr y; secur
e long hair and
roll up long slee
ves .
6. Disc onnec t po wer bef
ore ser
vice, ma
intenanc
e, or adjustments
.
7. DO NO
T oper ate when tir
ed or unde
r the influence of
drugs or alc
ohol.
8. Make sur
e the mac
hine is proper
ly adjuste
d/set up bef
ore star
ting .
9. Change c
utting fluid r
egular ly and av
oid c ontac t with skin.
10. Make sur
e w orkpiec
e is pro
per ly and sec
urely held in the chuc
k and has
safe c lear ance through full rota
tion bef ore star
ting the la
the.
11. Nev er leav
e the chuc
k ke y in the
chuck.
12. Nev er touch the chuc
k or w orkpiec
e when it i
s in motion.
13. Nev er leav
e the la
the running
una ttended.
14. Make sur
e long w
orkpieces ar
e prop
erly suppor
ted.
15. Always use the proper
speed r
ate f or the ma
terial y
ou ar e tur ning .
16. Do not allo
w c hildr en to hav
e unsuper
vised ac
cess to the mac
hine.
WA RNI NG !
!
Motor : 7.5HP
, 220V , 3-Ph,
60Hz
Full -Load Cur
rent Rati ng: 21.
7A
Swing
Ov er Bed: 16.
14"
Dist ance Between Cent
ers: 40"
Swing ov er cross
slide: 10.
375"
Swing ov er ga p: 22.95"
Spi ndl e nose t
o gap (m
ax.): 6.
5"
Cros s sli de tr avel : 9"
Compound t
rav el: 5. 1"
Spi ndl e Nose:
D1-6 Camlock
Spi ndl e Bor e: 2-1/16
"
Taper Ins
ide Spi
ndle: MT#6
Taper Ins
ide T ailst ock: MT#4
Wei ght: 3080 lbs
.
2416
2407
2318 2318-1
2318-3
2318-2