Sharp DT-200 - Manual (Page 54)

E-53
Appendix
Specifications
Product type
Model
Video system
Display method
DLP panel
Lens
Projection lamp
Video input signal
S-video input signal
Component input signal
(INPUT 1)
Component input signal
(INPUT 2)
Component RGB input signal
(INPUT 2)
Horizontal resolution
RGB input signal
Pixel clock
Vertical frequency
Horizontal frequency
Rated voltage
Input current
Rated frequency
Power consumption
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Projector
DT-200
PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480i/480P/720P/1080i
DLP chip, RGB optical shutter method
Panel size: 0.55
Љ
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 480,000 dots (800 [H]
ן 600 [V])
1–1.2 ן zoom lens, F3.0, f=32.5–44.0 mm
150 W SHP lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75
Ω
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75
Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA Connector
Y: 1.0 Vp-p, sync negative, 75
Ω terminated
P B : 0.7 Vp-p, 75 Ω terminated
P R : 0.7 Vp-p, 75 Ω terminated
29-pin connector
DVI input signal: Digital 250–1,000 mV 50
Ω
Analog 0.7 Vp-p 75 Ω
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P B : 0.7 Vp-p, 75 Ω terminated
P R : 0.7 Vp-p, 75 Ω terminated
29-pin connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75
Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
520 TV lines (NTSC 3.58 input)
15-
PIN MINI D- SUB CONNECTOR (INPUT 2):
RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive,
75
Ω terminated
H ORIZONTAL SYNC . SIGNAL : TTL level (positive/negative) or composite sync (Apple only)
V ERTICAL SYNC . SIGNAL : Same as above
12–110 MHz
43–75 Hz
15–70 kHz
AC 100–240 V
2.1 A
50/60 Hz
200 W
750 BTU/hour
41
°F to 95°F (ם5°C to ם35°C)
מ4°F to 140°F (מ20°C to ם60°C)
Plastic
38 kHz
14
1 ⁄ 2
Љ (W) ן 6 9 ⁄ 16
Љ (H) ן 12 7 ⁄ 8
Љ (D) (368 ן 153.8 ן 327 mm) (including swivel stand)
14 1 ⁄
2
Љ (W) ן 4 5 ⁄
8
Љ (H) ן 12 7 ⁄
8
Љ (D) (368 ן 118 ן 327 mm) (main body only)
9.5 lbs. (4.3 kg) (including swivel stand)
8.4 lbs. (3.8kg) (main body only)
Remote control, Two AA size batteries, Power cord, Video cable, Lens cap (attached on
the body), Lens cap strap, Operation manual
Lamp unit (Lamp/cage module) (BQC-XVZ90+++1), Remote control (RRMCGA088WJSA),
AA size batteries, Power cord (QACCDA007WJPZ), Video cable (QCNWGA001WJZZ),
Lens cap (CCAPHA004WJ01), Lens cap strap (UBNDT0013CEZZ), Operation manual
(TINS-A287WJZZA)
This SHARP projector uses a DMD chip. This very sophisticated chip
contains 480,000 pixels. As with any high technology electronic
equipment such as large screen TVs, video systems and video
cameras, there are certain acceptable tolerances that the equipment
must conform to. This unit has some inactive pixels within acceptable tolerances which
may result in inactive dots on the picture screen. This will not affect
the picture quality or the life expectancy of the unit. If you have any
questions about this matter, please call toll free 1-800-BE-SHARP (1-
800-237-4277).
U.S.A. ONLY
Specifications are subject to change without notice.
DT-200(E)#p50_59.p65 02.11.21, 11:45 AM 53