Sharp CD-BA2100 User Manual
Page 14
<P=004>
RECORDING
●
When recording important selections, be sure to
make a preliminary test to ensure that the desired
material is being properly recorded.
●
The VOLUME, X-BASS and EQUALIZER controls
may be adjusted with no effect on the recorded sig-
nal (Variable Sound Monitor).
●
Metal and CrO
2
tapes should not be used for recording or
dubbing.
■
Recording from the built-in CD player
(CD Synchronized Recording System)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button and load the desired disc.
●
Use the APMS function to store the tracks you want to record
in memory. (See page 10.)
3
Load a cassette into the TAPE 2 cassette compartment.
4
Press the REC PAUSE (
●
6
) button.
●
"SYNC" and "REC" will flash.
5
Press the
0 /R
(TAPE 2
0
) button.
●
"SYNC" will disappear and "REC" will light up.
●
CD playback will start approximately 5 seconds after the tape
starts.
To stop recording:
Press the
■
(CD
■
) button.
The CD and tape will stop.
Note:
●
When the end of the tape is reached while recording, the CD
player will display the track number which was being played
at that time, and stop automatically.
TAPE
TAPE 2
TUNER
(BAND)
REC PAUSE
CD
ON/
STAND-BY
CD
CD
TUNER
(BAND)
TAPE
(1 2)
TAPE(1 2)
TAPE 1 TAPE 2
POWER
ON/
STAND-BY
If you want to restart recording from the beginning of the in-
terrupted track, turn over the tape, press the REC PAUSE
(
●
6
) button and then the
0/R
(TAPE 2
0
) button.
(If tracks have been stored in memory using the APMS func-
tion, recording will restart from the first track stored in
memory.)
■
Dubbing from tape to tape
1
Press the ON/STAND-BY button to turn the power on.
2
Load a prerecorded cassette into the TAPE 1 cassette com-
partment. Insert a blank tape into the TAPE 2 cassette com-
partment.
●
It is recommended that the recording tape be the same length
as the master tape.
3
Press the TAPE (1
V
2) button until "TAPE 1" appears in the
display.
4
Press the REC PAUSE (
●
6
) button.
5
Press the
0 / R
(TAPE 2
0
) button.
To stop dubbing:
Press the
■
(TAPE
■
) button.
●
TAPE 1 and TAPE 2 will simultaneously stop.
■
Erasing recorded tapes
●
Make sure that TAPE 1 is not in use.
1
Load the tape to be erased into the TAPE 2 cassette com-
partment.
2
Press the TAPE (1
V
2) button until "TAPE 2" appears in the
display.
3
Press the REC PAUSE(
●
6
) button.
4
Press the
0 / R
(TAPE 2
0
) button.
■
Recording from the built-in radio
1
Tune in to the desired station. (See pages 11-12.)
2
Load a cassette into the TAPE 2 cassette compart-
ment.
3
Press the REC PAUSE (
●
6
) button.
●
"REC" will flash.
4
Press the
0 / R
(TAPE 2
0
) button.
●
"REC" will appear.
Note:
●
If a whistling noise is heard while recording from an
AM station, move the AM loop antenna to a position
where noise is no longer heard from the unit.
To stop recording:
Press the
■
(TAPE
■
) button.
CD-BA2100(SEC) TINSE0283AWZZ
13