Essex Electronics KE-265 - Manual (Page 10)

16
Programming User Codes
To Program a New User Code or Change an Existing User
Code:
1. Choose a new 3 to 8 digit code that will be used for this
User Code. ___ ___ ___ ___ ___ ___ ___ ___
2. Decide which User Location to place this User Code
(see Overview of User Codes)
3. Enter the Master Code, followed by the User Location
(you will hear three rapid beeps) and immediately enter
the new User Code. (Do not let more than five seconds
elapse between entries or the system will reset!!!)
Example: 1-3-5-7-9 1-1-1 1-2-3-4
4. After entering your new code, wait five seconds for the
3 reset beeps.
To Delete a User Code
1. Enter the Master Code, followed by the User Location
of the User Code you want to delete (you will hear
three rapid beeps). Example: 1-3-5-7-9 1-1-1
2. Wait five seconds for the 3 reset beeps (Do not enter
any digits until you hear 3 reset beeps)
Programming Door Open Time Default Î 5 seconds
To Program/Change the Door Open Time for the Master Code
and User Code 1 and 2:
1. First determine the length of time you wish to program
as the Door Open Time for these users. This is the
length of time the door will remain open after a valid
Master Code, User Code 1 or User Code 2 has been
entered into the system.
 Note: For controlling a garage door or electric gate,
you will need to set the door open time to 1 second
2. Locate the Control Module, remove the cover and
locate the “PROGRAM” switch on the circuit board.
3. Press the PROGRAM switch once *. (The Keypad will
beep rapidly 4 times)
4. At the Keypad, enter 1-1-1-7 to open the memory (you
will hear three rapid beeps) and enter a combination of
“1’s” (for every one second increment) and
17
“5’s” (for every five second increment) that equal your
desired Door Open Time. Each valid key press (a “1” or
a “5”) will generate a double beep. (Do not let more
than five seconds elapse between entries or the
system will reset!!!)
Example: “1-1-1-7 5-5-5-1-1” Î 17 seconds
5. After entering your Door Open Time, wait five seconds
for the 3 reset beeps.
To Program/Change the Door Open Time for User Code 3,4
and 5:
(Rev B and later)
1. First determine the length of time you wish to program
as the Door Open Time for these users. This is the
length of time the door will remain open after a valid
User Code 3, User Code 4 or User Code 5 has been
entered into the system.
 Note: For controlling a garage door or electric gate,
you will need to set the door open time to 1 second.
2. Locate the Control Module, remove the cover and
locate the “PROGRAM” switch on the circuit board.
3. Press the PROGRAM switch once *. (The Keypad will
beep rapidly 4 times)
4. At the Keypad, enter 1-1-1-5 to open the memory (you
will hear three rapid beeps) and enter a combination of
“1’s” (for every one second increment) and “5’s” (for
every five second increment) that equal your desired
Door Open Time. Each valid key press (a “1” or a “5”)
will generate a double beep. (Do not let more than five
seconds elapse between entries or the system will
reset!!!)
Example: “1-1-1-5 1-1-5” Î 7 seconds
5. After entering your Door Open Time, wait five seconds
for the 3 reset beeps.
 Notes: * Once the PROGRAM switch has been pressed,
you have 2 minutes to begin programming. You will hear a
double beep with each valid key press. Once you begin
entering the combination of 1’s and 5’s do not let more
than five seconds elapse between entries or the system
will reset!!! Maximum Door Open Time is 120 seconds
.