Skylink MA-103 - Manual (Page 2)

Start with removing 1
2. SET UP - TEST MODE
To set the Control Panel in Test Mode:
Step 1: Remove the adapter and all batteries from the Control Panel.
Step 2: Press and hold the "Mute" button and plug the AC adapter back into the Control
Panel. All LED indicators will be ON, you may release the "Mute" button. Control
Panel is now in Test Mode, and it will respond to all sensor activations.
Step 3: Place the Alert Notification Switch to "Alert" and you may now activate the sensors,
i.e. by pressing the test button on the Motion Sensor or separating the magnet from
the Door / Window Sensor.
Step 4: Control Panel will respond by flashing the zone LED and alert beeping, according to the
zone number. 1 beep for zone 1, 2 beeps for zone 2 etc.
Hold “Mute”, don’t release
until step 4. 2
Plug in Power, all zone LEDs
ON. 3
Start with removing all power
from Control Panel. 1
Release “Mute”. 4
Activate sensors for testing. 5
After testing, unplug the AC adapter and plugs it back into the Control Panel, it will back to Normal Operating Mode.
2. SET UP - PASSWORD
The Password is used for arming and disarming the Control Panel. The factory default Password
is [1234]. It is recommended to setup your own Password by following the steps below.
Step 1: Press and hold the “Learn” button.
Step 2: While holding the “Learn” button, press and hold the “Arm” button (you are now
pressing and holding both “Learn” and “Arm” buttons. Hold them for 3 seconds
until you hear a long beep and the green Power LED flashes.
Step 3: Release all buttons. Enter the current Password. (If new, the factory default
Password is [1234]), you will hear 2 beeps.
Step 4: Enter the new 4-digit Password, you will hear 2 beeps.
Step 5: Enter the new 4-digit Password again to confirm. A long beep will sound and the green LED will stop flashing indicating your
new Password has been set.
MU TE
MU TE
IN PU T D C 12 V
IN PU T D C 12 V
LE AR N
LE AR N
AL ER T
AL ER T
CH IM E
CH IM E
OF F
OF F
Hold “Learn”
Hold both
buttons for
3 seconds
until hear
long beep.
1
Hold “Arm” 2
Release all buttons, enter
current Password (1234) 3
}
Enter new password (1111) 4
Enter new password (1111)
Password is now changed from
1234 to 1111.
5
Long beep confirm
2. SET UP - ERASE SENSORS
To erase a sensor from a zone, the Control Panel will erase all sensors in that zone.
So any other sensors will need to be programmed back to that particular zone.
To erase a zone:
Step 1: Press and hold the “Learn” button on the Control Panel. The
unit will beep once.
Step 2: While holding the “Learn” button, press and hold the Zone
button to be erased. Hold both buttons for 5 seconds until the
Control Panel emits 2 beeps and the zone LED flashes twice.
Step 3: Release all buttons.
MU TE
MU TE
IN PU T D C 12 V
IN PU T D C 12 V
LE AR N
LE AR N
AL ER T
AL ER T
CH IM E
CH IM E
OF F
OF F
Hold “Learn”
Hold both
buttons for
5 seconds.
1
Hold zone button 2
Release all buttons until hearing
2 beeps. 3
}
Beep once
3. ALERT - OPERATION
Alert notification is provided when any sensor is activated while the system is disarmed. Different alert notification can
be provided depends on the setting of the Alert Notification Switch on the side of the Control Panel.
Alert Notification Switch
OFF
CHIME
ALERT
Audio Alert
None
Chime Once when sensor is activated
Alert beeping depends on zone number
Zone LED Flashing
Yes
Yes
Yes
If the Alert Notification Switch is set to “Alert”, the number of beeps depends on what zone is activated.
The beeping will continue until the sensor is deactivated, i.e. door is closed, or water sensor doesn't detect water anymore.
Example:
Zone 1 sensor: “1 beep, pause, 1 beep, pause, 1 beep, pause… etc”
Zone 2 sensor: “2 beeps, pause, 2 beeps, pause, 2 beeps, pause… etc”
Zone 3 sensor: “3 beeps, pause, 3 beeps, pause, 3 beeps, pause… etc”
Zone 4 sensor: “4 beeps, pause, 4 beeps, pause, 4 beeps, pause… Etc”
- Beep
- Beep
Zone 1
Door /
Window
Sensor
Zone 2
Water
Sensor - Beep Beep
- Beep Beep
3. ALERT - MUTE
4. ALARM
To temporarily disable the beeping while it is sounding, you may press the “Mute” button on the side of the Control Panel. It will stop all the current beeping.
This is useful when a window will be opened for awhile for ventilation.
To deactivate the mute, reset the sensor (i.e. close the window), the mute function will be deactivated so if the window sensor is activated again, the beeping will continue.
Note: Motion Sensor in Zone 1, 2 and 3 will not respond in Alert mode, i.e. when system is disarmed. Motion Sensors in Zones 1, 2 and 3 will only respond when the Control
Panel is armed. If you would like to have alert indication for Motion Sensor, you must program the Motion Sensor in Zone 4.
You may arm the Control Panel in 2 different ways:
1) Arm Home 2) Arm Away
4. ALARM - ARM HOME
This setting is used when you wish to secure the area but will be at home and moving around within the armed area. In Arm Home setting, any Motion Sensors in Zone 1, 2,
and 3 will not respond to any movement.
Alarm will sound instantly if any of the sensor in Zone 1, 2, and 3 is activated (except Motion Sensor).